RTL8139 changes: The PCI memory BAR is now 4096 bytes instead of 256 in order to fit into 86Box's memory mapping granularity, and implemented the undocumented CSCR reads discovered by RichardG when probing the real hardware.

src/network/net_rtl8139.c

@@ -308,6 +308,8 @@ enum CSCRBits {
 #endif
 enum CSCRBits {
     CSCR_Testfun       = 1 << 15, /* 1 = Auto-neg speeds up internal timer, WO, def 0 */
+    CSCR_Cable_Changed = 1 << 11, /* Undocumented: 1 = Cable status changed, 0 = No change */
+    CSCR_Cable         = 1 << 10, /* Undocumented: 1 = Cable connected, 0 = Cable disconnected */
     CSCR_LD            = 1 << 9,  /* Active low TPI link disable signal. When low, TPI still transmits link pulses and TPI stays in good link state. def 1*/
     CSCR_HEART_BIT     = 1 << 8,  /* 1 = HEART BEAT enable, 0 = HEART BEAT disable. HEART BEAT function is only valid in 10Mbps mode. def 1*/
     CSCR_JBEN          = 1 << 7,  /* 1 = enable jabber function. 0 = disable jabber function, def 1*/
@@ -2285,7 +2287,17 @@ rtl8139_TSAD_read(RTL8139State *s)
 static uint16_t
 rtl8139_CSCR_read(RTL8139State *s)
 {
-    uint16_t ret = s->CSCR;
+    static uint16_t old_ret = 0xffff;
+    uint16_t ret = s->CSCR |
+                   ((net_cards_conf[s->nic->card_num].link_state & NET_LINK_DOWN) ? 0 : CSCR_Cable);
+
+    if (old_ret != 0xffff) {
+        ret &= ~CSCR_Cable_Changed;
+        if ((ret ^ old_ret) & CSCR_Cable)
+            ret |= CSCR_Cable_Changed;
+    }
+
+    old_ret = ret;
 
     rtl8139_log("CSCR read val=0x%04x\n", ret);
 
@@ -2736,6 +2748,13 @@ rtl8139_io_readb(uint32_t addr, void *priv)
             rtl8139_log("RTL8139C TxConfig at 0x43 read(b) val=0x%02x\n", ret);
             break;
 
+        case CSCR:
+            ret = rtl8139_CSCR_read(s) & 0xff;
+            break;
+        case CSCR + 1:
+            ret = rtl8139_CSCR_read(s) >> 8;
+            break;
+
         default:
             rtl8139_log("not implemented read(b) addr=0x%x\n", addr);
             ret = 0;
@@ -3105,6 +3124,10 @@ rtl8139_pci_read(UNUSED(int func), int addr, void *priv)
             return 1;
         case 0x14:
             return 0;
+#ifndef USE_256_BYTE_BAR
+        case 0x15:
+            return s->pci_conf[addr & 0xFF] & 0xf0;
+#endif
         case 0x2c:
             return 0xEC;
         case 0x2d:
@@ -3169,10 +3192,20 @@ rtl8139_pci_write(int func, int addr, uint8_t val, void *priv)
         case 0x16:
         case 0x17:
             s->pci_conf[addr & 0xFF] = val;
-            s->mem_base = (s->pci_conf[0x15] << 8) | (s->pci_conf[0x16] << 16) | (s->pci_conf[0x17] << 24); 
+            s->mem_base = (s->pci_conf[0x15] << 8) | (s->pci_conf[0x16] << 16) |
+                          (s->pci_conf[0x17] << 24);
+#ifndef USE_256_BYTE_BAR
+            s->mem_base &= 0xfffff000;
+#endif
             rtl8139_log("New memory base: %08X\n", s->mem_base);
             if (s->pci_conf[0x4] & PCI_COMMAND_MEM)
-                mem_mapping_set_addr(&s->bar_mem, (s->pci_conf[0x15] << 8) | (s->pci_conf[0x16] << 16) | (s->pci_conf[0x17] << 24), 256);
+#ifdef USE_256_BYTE_BAR
+                mem_mapping_set_addr(&s->bar_mem, (s->pci_conf[0x15] << 8) | (s->pci_conf[0x16] << 16) |
+                                     (s->pci_conf[0x17] << 24), 256);
+#else
+                mem_mapping_set_addr(&s->bar_mem, ((s->pci_conf[0x15] & 0xf0) << 8) |
+                                     (s->pci_conf[0x16] << 16) | (s->pci_conf[0x17] << 24), 4096);
+#endif
             break;
         case 0x3c:
             s->pci_conf[addr & 0xFF] = val;