smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.4 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST250DM000-1BD141
Serial Number:    --
LU WWN Device Id: 5 000c50 ...
Firmware Version: KC45
User Capacity:    250,059,350,016 bytes [250 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Oct 25 22:05:54 2023 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  600) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  42) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x303f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   112   096   006    Pre-fail  Always       -       44658040
  3 Spin_Up_Time            0x0003   100   097   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   091   091   020    Old_age   Always       -       10188
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   085   060   030    Pre-fail  Always       -       369650229
  9 Power_On_Hours          0x0032   051   051   000    Old_age   Always       -       43451
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   020    Old_age   Always       -       4337
183 Runtime_Bad_Block       0x0032   098   098   000    Old_age   Always       -       2
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   001   001   000    Old_age   Always       -       407
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 1
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   067   051   045    Old_age   Always       -       33 (Min/Max 17/36)
194 Temperature_Celsius     0x0022   033   049   000    Old_age   Always       -       33 (0 14 0 0 0)
195 Hardware_ECC_Recovered  0x001a   048   030   000    Old_age   Always       -       44658040
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       1
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       28785h+17m+29.838s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       613334677
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       935419298

SMART Error Log Version: 1
ATA Error Count: 399 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 399 occurred at disk power-on lifetime: 17867 hours (744 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 ff ff ff 4f 00      00:34:30.763  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:26.909  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:23.037  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:19.241  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:15.481  READ DMA EXT

Error 398 occurred at disk power-on lifetime: 17867 hours (744 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 ff ff ff 4f 00      00:34:26.909  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:23.037  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:19.241  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:15.481  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.477  READ DMA EXT

Error 397 occurred at disk power-on lifetime: 17867 hours (744 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 ff ff ff 4f 00      00:34:23.037  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:19.241  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:15.481  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.477  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.471  READ DMA EXT

Error 396 occurred at disk power-on lifetime: 17867 hours (744 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 ff ff ff 4f 00      00:34:19.241  READ DMA EXT
  25 00 00 ff ff ff 4f 00      00:34:15.481  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.477  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.471  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.468  READ DMA EXT

Error 395 occurred at disk power-on lifetime: 17867 hours (744 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 00 ff ff ff 4f 00      00:34:15.481  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.477  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.471  READ DMA EXT
  25 00 40 ff ff ff 4f 00      00:34:15.468  READ DMA EXT
  c8 00 00 00 9b d9 eb 00      00:34:15.466  READ DMA

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     16727         -
# 2  Extended offline    Aborted by host               90%     16726         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

The above only provides legacy SMART information - try 'smartctl -x' for more



