smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST380815AS
Serial Number:    --
Firmware Version: 4.AAB
User Capacity:    80,026,361,856 bytes [80.0 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Fri Feb 19 16:40:03 2021 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  27) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   100   253   006    -    0
  3 Spin_Up_Time            PO----   097   097   000    -    0
  4 Start_Stop_Count        -O--CK   092   092   020    -    8462
  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0
  7 Seek_Error_Rate         POSR--   084   060   030    -    284909397
  9 Power_On_Hours          -O--CK   094   094   000    -    5695
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   094   094   020    -    7020
187 Reported_Uncorrect      -O--CK   001   001   000    -    2180
189 High_Fly_Writes         -O-RCK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   064   045   045    Past 36 (Min/Max 24/36)
194 Temperature_Celsius     -O---K   036   055   000    -    36 (0 14 0 0 0)
195 Hardware_ECC_Recovered  -O-RC-   069   063   000    -    19047142
197 Current_Pending_Sector  -O--C-   100   100   000    -    1
198 Offline_Uncorrectable   ----C-   100   100   000    -    1
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    809
200 Multi_Zone_Error_Rate   ------   100   253   000    -    0
202 Data_Address_Mark_Errs  -O--CK   100   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      5  Comprehensive SMART error log
0x03       GPL,SL  R/O      5  Ext. Comprehensive SMART error log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      1  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  NCQ Command Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters log
0x20       GPL,SL  R/O      1  Streaming performance log [OBS-8]
0x21       GPL,SL  R/O      1  Write stream error log
0x22       GPL,SL  R/O      1  Read stream error log
0x23       GPL,SL  R/O      1  Delayed sector log [OBS-8]
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0       GPL,SL  VS       1  Device vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL,SL  VS     101  Device vendor specific log
0xa8       GPL,SL  VS      20  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer
0xff       GPL     -    23040  Reserved

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 2205 (device log contains only the most recent 20 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2205 [4] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:32.309  READ DMA
  ca 00 00 00 08 00 01 05 00 62 2f e1 00     00:48:32.303  WRITE DMA
  c8 00 00 00 08 00 00 70 00 61 67 e0 00     00:48:32.287  READ DMA
  ca 00 00 00 08 00 00 f6 00 5b 6f e0 00     00:48:28.810  WRITE DMA
  ca 00 00 00 10 00 00 5a 00 3c 67 e0 00     00:48:28.802  WRITE DMA

Error 2204 [3] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:43.265  READ DMA
  c8 00 00 00 20 00 00 07 00 14 0d e0 00     00:48:43.259  READ DMA
  ca 00 00 00 08 00 00 be 00 06 7f e0 00     00:48:43.258  WRITE DMA
  c8 00 00 00 08 00 04 53 00 36 47 e4 00     00:48:43.243  READ DMA
  c8 00 00 00 08 00 04 0b 00 36 07 e4 00     00:48:43.243  READ DMA

Error 2203 [2] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:39.281  READ DMA
  c8 00 00 00 08 00 00 30 00 62 b7 e0 00     00:48:39.281  READ DMA
  ca 00 00 00 08 00 00 f6 00 5b 7f e0 00     00:48:39.280  WRITE DMA
  ca 00 00 00 08 00 00 5a 00 3c 17 e0 00     00:48:39.280  WRITE DMA
  ca 00 00 00 08 00 00 76 00 31 2f e0 00     00:48:39.279  WRITE DMA

Error 2202 [1] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:35.796  READ DMA
  c8 00 00 00 08 00 00 2c 00 62 df e0 00     00:48:35.796  READ DMA
  c8 00 00 00 08 00 00 73 00 61 87 e0 00     00:48:35.790  READ DMA
  ca 00 00 00 18 00 00 2b 00 5d 57 e0 00     00:48:35.782  WRITE DMA
  ca 00 00 00 99 00 00 9e 00 47 ef e0 00     00:48:35.766  WRITE DMA

Error 2201 [0] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:32.309  READ DMA
  ca 00 00 00 08 00 01 05 00 62 2f e1 00     00:48:32.303  WRITE DMA
  c8 00 00 00 08 00 00 70 00 61 67 e0 00     00:48:32.287  READ DMA
  ca 00 00 00 08 00 00 f6 00 5b 6f e0 00     00:48:28.810  WRITE DMA
  ca 00 00 00 10 00 00 5a 00 3c 67 e0 00     00:48:28.802  WRITE DMA

Error 2200 [19] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:43.265  READ DMA
  c8 00 00 00 20 00 00 07 00 14 0d e0 00     00:48:43.259  READ DMA
  ca 00 00 00 08 00 00 be 00 06 7f e0 00     00:48:43.258  WRITE DMA
  c8 00 00 00 08 00 04 53 00 36 47 e4 00     00:48:43.243  READ DMA
  c8 00 00 00 08 00 04 0b 00 36 07 e4 00     00:48:43.243  READ DMA

Error 2199 [18] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:39.281  READ DMA
  c8 00 00 00 08 00 00 30 00 62 b7 e0 00     00:48:39.281  READ DMA
  ca 00 00 00 08 00 00 f6 00 5b 7f e0 00     00:48:39.280  WRITE DMA
  ca 00 00 00 08 00 00 5a 00 3c 17 e0 00     00:48:39.280  WRITE DMA
  ca 00 00 00 08 00 00 76 00 31 2f e0 00     00:48:39.279  WRITE DMA

Error 2198 [17] occurred at disk power-on lifetime: 3186 hours (132 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 c4 00 92 5a e1 00  Error: UNC at LBA = 0x1c500925a = 7600116314

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 01 c4 00 92 57 e1 00     00:48:35.796  READ DMA
  c8 00 00 00 08 00 00 2c 00 62 df e0 00     00:48:35.796  READ DMA
  c8 00 00 00 08 00 00 73 00 61 87 e0 00     00:48:35.790  READ DMA
  ca 00 00 00 18 00 00 2b 00 5d 57 e0 00     00:48:35.782  WRITE DMA
  ca 00 00 00 99 00 00 9e 00 47 ef e0 00     00:48:35.766  WRITE DMA

SMART Extended Self-test Log Version: 1 (1 sectors)

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2           17  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS



