smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST500DM002-1BD142
Serial Number:    --
LU WWN Device Id: 5 000c50 ...
Firmware Version: KC48
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Apr 29 10:48:59 2024 -03
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Disabled
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  592) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  77) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x303f)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   110   073   006    -    29256144
  3 Spin_Up_Time            PO----   100   099   000    -    0
  4 Start_Stop_Count        -O--CK   098   098   020    -    3068
  5 Reallocated_Sector_Ct   PO--CK   097   097   036    -    1048
  7 Seek_Error_Rate         POSR--   080   060   030    -    112936307
  9 Power_On_Hours          -O--CK   061   061   000    -    34885
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   098   098   020    -    3063
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        -O--CK   100   100   099    -    0
187 Reported_Uncorrect      -O--CK   001   001   000    -    20644
188 Command_Timeout         -O--CK   100   100   000    -    0 0 0
189 High_Fly_Writes         -O-RCK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   059   047   045    -    41 (Min/Max 37/50)
194 Temperature_Celsius     -O---K   041   053   000    -    41 (0 16 0 0 0)
195 Hardware_ECC_Recovered  -O-RC-   043   025   000    -    29256144
197 Current_Pending_Sector  -O--C-   095   070   000    -    208
198 Offline_Uncorrectable   ----C-   095   070   000    -    208
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
240 Head_Flying_Hours       ------   100   253   000    -    34854h+29m+49.376s
241 Total_LBAs_Written      ------   100   253   000    -    2104624004
242 Total_LBAs_Read         ------   100   253   000    -    359488260
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      5  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL     VS    2248  Device vendor specific log
0xa8       GPL,SL  VS     129  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xab       GPL     VS       1  Device vendor specific log
0xb0       GPL     VS    2928  Device vendor specific log
0xbd       GPL     VS     252  Device vendor specific log
0xbe-0xbf  GPL     VS   65535  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 20615 (device log contains only the most recent 20 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 20615 [14] occurred at disk power-on lifetime: 27664 hours (1152 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e 40 34 00 00  Error: UNC at LBA = 0x106e4034 = 275660852

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 04 00 00 10 6e 40 34 40 00     00:32:36.409  READ FPDMA QUEUED
  27 00 00 00 00 00 00 00 00 00 00 e0 00     00:32:36.409  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 00     00:32:36.408  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 00     00:32:36.408  SET FEATURES [Set transfer mode]
  27 00 00 00 00 00 00 00 00 00 00 e0 00     00:32:36.381  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 20614 [13] occurred at disk power-on lifetime: 27664 hours (1152 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e 40 30 00 00  Error: UNC at LBA = 0x106e4030 = 275660848

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 04 00 00 10 6e 40 34 40 00     00:32:32.639  READ FPDMA QUEUED
  60 00 00 00 04 00 00 10 6e 40 30 40 00     00:32:32.638  READ FPDMA QUEUED
  27 00 00 00 00 00 00 00 00 00 00 e0 00     00:32:32.638  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 00 00 00 00 00 a0 00     00:32:32.636  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 00     00:32:32.636  SET FEATURES [Set transfer mode]

Error 20613 [12] occurred at disk power-on lifetime: 27664 hours (1152 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e 40 30 00 00  Error: UNC at LBA = 0x106e4030 = 275660848

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 0a 00 00 00 10 6e 40 30 40 00     00:32:28.855  READ FPDMA QUEUED
  60 00 00 0a 00 00 00 10 40 d1 a8 40 00     00:32:28.837  READ FPDMA QUEUED
  60 00 00 0a 00 00 00 10 40 c7 a8 40 00     00:32:28.825  READ FPDMA QUEUED
  60 00 00 04 58 00 00 10 40 2f 60 40 00     00:32:28.815  READ FPDMA QUEUED
  60 00 00 00 f0 00 00 10 3f 5d 18 40 00     00:32:28.814  READ FPDMA QUEUED

Error 20612 [11] occurred at disk power-on lifetime: 27590 hours (1149 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e e2 f7 00 00  Error: WP at LBA = 0x106ee2f7 = 275702519

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 08 00 00 0d 59 b0 f8 40 00  1d+03:34:42.299  WRITE FPDMA QUEUED
  61 00 00 00 10 00 00 00 51 47 40 40 00  1d+03:34:42.299  WRITE FPDMA QUEUED
  61 00 00 00 10 00 00 03 63 b3 30 40 00  1d+03:34:42.299  WRITE FPDMA QUEUED
  61 00 00 00 10 00 00 05 fa 4f f8 40 00  1d+03:34:42.299  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 0a ee c9 e0 40 00  1d+03:34:42.298  WRITE FPDMA QUEUED

Error 20611 [10] occurred at disk power-on lifetime: 27590 hours (1149 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e e2 f6 00 00  Error: WP at LBA = 0x106ee2f6 = 275702518

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 08 00 00 05 fa 6c 50 40 00  1d+03:34:38.360  WRITE FPDMA QUEUED
  61 00 00 00 10 00 00 00 50 96 80 40 00  1d+03:34:38.360  WRITE FPDMA QUEUED
  60 00 00 00 01 00 00 10 6e e2 f6 40 00  1d+03:34:38.359  READ FPDMA QUEUED
  61 00 00 00 08 00 00 0d 59 a0 a8 40 00  1d+03:34:38.359  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 0a ee ca c8 40 00  1d+03:34:38.359  WRITE FPDMA QUEUED

Error 20610 [9] occurred at disk power-on lifetime: 27590 hours (1149 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e e2 f5 00 00  Error: UNC at LBA = 0x106ee2f5 = 275702517

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 3d 00 00 05 0e bf a3 40 00  1d+03:34:34.605  READ FPDMA QUEUED
  60 00 00 00 01 00 00 10 6e e2 f5 40 00  1d+03:34:34.602  READ FPDMA QUEUED
  60 00 00 00 08 00 00 12 77 81 20 40 00  1d+03:34:34.585  READ FPDMA QUEUED
  60 00 00 00 30 00 00 29 83 06 08 40 00  1d+03:34:34.501  READ FPDMA QUEUED
  60 00 00 00 38 00 00 02 f4 e9 48 40 00  1d+03:34:34.501  READ FPDMA QUEUED

Error 20609 [8] occurred at disk power-on lifetime: 27590 hours (1149 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e e2 f4 00 00  Error: UNC at LBA = 0x106ee2f4 = 275702516

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 01 00 00 10 6e e2 f4 40 00  1d+03:34:30.626  READ FPDMA QUEUED
  61 00 00 00 08 00 00 0a ee ca 48 40 00  1d+03:34:30.626  WRITE FPDMA QUEUED
  60 00 00 00 80 00 00 10 73 9f 30 40 00  1d+03:34:30.625  READ FPDMA QUEUED
  61 00 00 00 30 00 00 0a ee ca a0 40 00  1d+03:34:30.624  WRITE FPDMA QUEUED
  60 00 00 00 38 00 00 02 eb eb a8 40 00  1d+03:34:30.616  READ FPDMA QUEUED

Error 20608 [7] occurred at disk power-on lifetime: 27590 hours (1149 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 10 6e e2 f3 00 00  Error: UNC at LBA = 0x106ee2f3 = 275702515

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 38 00 00 02 eb eb a8 40 00  1d+03:34:26.873  READ FPDMA QUEUED
  60 00 00 00 01 00 00 10 6e e2 f3 40 00  1d+03:34:26.870  READ FPDMA QUEUED
  60 00 00 00 40 00 00 06 fc cd 80 40 00  1d+03:34:26.855  READ FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00  1d+03:34:26.482  SET FEATURES [Disable SATA feature]
  ef 00 02 00 00 00 00 00 00 00 00 a0 00  1d+03:34:26.399  SET FEATURES [Enable write cache]

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%         0         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       522 (0x020a)
Device State:                        Active (0)
Current Temperature:                    41 Celsius
Power Cycle Min/Max Temperature:     37/50 Celsius
Lifetime    Min/Max Temperature:     16/53 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        59 minutes
Min/Max recommended Temperature:     14/55 Celsius
Min/Max Temperature Limit:           10/60 Celsius
Temperature History Size (Index):    128 (97)

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2           43  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS

