smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.1-RELEASE amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Laptop HDD
Device Model:     ST500LM021-1KJ152
Serial Number:    --
LU WWN Device Id: 5 000c50 ...
Firmware Version: 0002LIM1
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Mon Sep 28 14:26:36 2020 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  82) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x1031)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   120   097   034    -    234940040
  3 Spin_Up_Time            PO----   098   098   000    -    0
  4 Start_Stop_Count        -O--CK   097   097   020    -    3186
  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0
  7 Seek_Error_Rate         POSR--   084   060   030    -    275856247
  9 Power_On_Hours          -O--CK   085   085   000    -    13739 (237 116 0)
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   098   098   020    -    2718
184 End-to-End_Error        -O--CK   100   100   099    -    0
187 Reported_Uncorrect      -O--CK   001   001   000    -    110
188 Command_Timeout         -O--CK   100   100   000    -    4295032833
189 High_Fly_Writes         -O-RCK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   077   050   045    -    23 (0 6 23 16 0)
191 G-Sense_Error_Rate      -O--CK   100   100   000    -    363
192 Power-Off_Retract_Count -O--CK   100   100   000    -    9
193 Load_Cycle_Count        -O--CK   001   001   000    -    365923
194 Temperature_Celsius     -O---K   023   050   000    -    23 (128 0 0 0 0)
196 Reallocated_Event_Count POSR--   088   088   030    -    10928 (16083 0)
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
254 Free_Fall_Sensor        -O--CK   100   100   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      5  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL     VS    2248  Device vendor specific log
0xa8       GPL,SL  VS      65  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xab       GPL     VS       1  Device vendor specific log
0xb0       GPL     VS    2864  Device vendor specific log
0xbd-0xbf  GPL     VS   65535  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL,SL  VS      10  Device vendor specific log
0xc3       GPL,SL  VS       8  Device vendor specific log
0xc4       GPL,SL  VS      18  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 110 (device log contains only the most recent 20 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 110 [9] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:41.623  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 a0 00     01:28:40.852  FLUSH CACHE EXT
  61 00 00 00 10 00 00 00 86 f7 b0 40 00     01:28:40.852  WRITE FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:40.791  SET FEATURES [Disable SATA feature]
  61 00 00 00 08 00 00 01 88 a2 f0 40 00     01:28:40.790  WRITE FPDMA QUEUED

Error 109 [8] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:38.890  READ FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:38.057  SET FEATURES [Disable SATA feature]
  ef 00 02 00 00 00 00 00 00 00 00 a0 00     01:28:38.006  SET FEATURES [Enable write cache]
  00 00 00 00 00 00 00 00 00 00 00 00 ff     01:28:37.886  NOP [Abort queued commands]
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:36.132  READ FPDMA QUEUED

Error 108 [7] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:36.132  READ FPDMA QUEUED
  61 00 00 00 08 00 00 00 86 f7 20 40 00     01:28:35.364  WRITE FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 a0 00     01:28:35.358  FLUSH CACHE EXT
  61 00 00 00 08 00 00 00 86 f7 30 40 00     01:28:35.358  WRITE FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:35.300  SET FEATURES [Disable SATA feature]

Error 107 [6] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:33.415  READ FPDMA QUEUED
  61 00 00 00 08 00 00 05 9a cb 30 40 00     01:28:32.643  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 08 29 04 08 40 00     01:28:32.643  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 8d 51 40 40 00     01:28:32.643  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 8b 70 88 40 00     01:28:32.642  WRITE FPDMA QUEUED

Error 106 [5] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:30.680  READ FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:27.931  SET FEATURES [Disable SATA feature]
  ef 00 02 00 00 00 00 00 00 00 00 a0 00     01:28:27.879  SET FEATURES [Enable write cache]
  00 00 00 00 00 00 00 00 00 00 00 00 ff     01:28:27.759  NOP [Abort queued commands]
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:26.007  READ FPDMA QUEUED

Error 105 [4] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:26.007  READ FPDMA QUEUED
  61 00 00 00 10 00 00 00 7f f3 70 40 00     01:28:25.493  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 7f f3 08 40 00     01:28:25.492  WRITE FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:25.149  SET FEATURES [Disable SATA feature]
  61 00 00 00 40 00 00 01 63 53 e0 40 00     01:28:25.148  WRITE FPDMA QUEUED

Error 104 [3] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: WP at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 40 00 00 01 63 53 a0 40 00     01:28:23.221  WRITE FPDMA QUEUED
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:23.221  READ FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:23.187  SET FEATURES [Disable SATA feature]
  61 00 00 00 40 00 00 01 63 54 20 40 00     01:28:23.187  WRITE FPDMA QUEUED
  ef 00 02 00 00 00 00 00 00 00 00 a0 00     01:28:23.169  SET FEATURES [Enable write cache]

Error 103 [2] occurred at disk power-on lifetime: 4072 hours (169 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 07 81 9d 30 00 00  Error: UNC at LBA = 0x07819d30 = 125934896

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 07 81 9d 30 40 00     01:28:21.319  READ FPDMA QUEUED
  61 00 00 00 08 00 00 00 60 35 60 40 00     01:28:20.574  WRITE FPDMA QUEUED
  ef 00 90 00 03 00 00 00 00 00 00 a0 00     01:28:20.496  SET FEATURES [Disable SATA feature]
  61 00 00 00 40 00 00 01 63 53 e0 40 00     01:28:20.496  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 60 35 20 40 00     01:28:20.495  WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Vendor (0x50)       Completed without error       00%      8510         -
# 2  Short offline       Completed without error       00%      8510         -
# 3  Vendor (0x50)       Completed without error       00%      8050         -
# 4  Short offline       Completed without error       00%      8050         -
# 5  Vendor (0x50)       Completed without error       00%      7468         -
# 6  Short offline       Completed without error       00%      7468         -
# 7  Vendor (0x50)       Completed without error       00%      6796         -
# 8  Short offline       Completed without error       00%      6796         -
# 9  Vendor (0x50)       Completed without error       00%      6052         -
#10  Short offline       Completed without error       00%      6052         -
#11  Vendor (0x50)       Completed without error       00%      5384         -
#12  Short offline       Completed without error       00%      5384         -
#13  Vendor (0x50)       Completed without error       00%      4681         -
#14  Short offline       Completed without error       00%      4680         -
#15  Vendor (0x50)       Completed without error       00%      4180         -
#16  Short offline       Completed without error       00%      4180         -
#17  Vendor (0x50)       Completed without error       00%      3981         -
#18  Short offline       Completed without error       00%      3981         -
#19  Vendor (0x50)       Completed without error       00%      3942         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       522 (0x020a)
Device State:                        Active (0)
Current Temperature:                    16 Celsius
Power Cycle Min/Max Temperature:     16/16 Celsius
Lifetime    Min/Max Temperature:     13/50 Celsius
Under/Over Temperature Limit Count:   0/1
Vendor specific:
00 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        11 minutes
Min/Max recommended Temperature:      0/ 0 Celsius
Min/Max Temperature Limit:            0/ 0 Celsius
Temperature History Size (Index):    128 (58)

SCT Error Recovery Control command not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            6  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS

