smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Laptop HDD
Device Model:     ST500LT012-1DG142
Serial Number:    --
LU WWN Device Id: 5 000c50 ...
Firmware Version: 0003SDM1
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database 7.3/5528
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Sat Jan  6 00:30:30 2024 MST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 101) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x1035)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   115   099   006    -    90955544
  3 Spin_Up_Time            PO----   099   099   000    -    0
  4 Start_Stop_Count        -O--CK   086   086   020    -    14943
  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0
  7 Seek_Error_Rate         POSR--   078   060   030    -    4374043186
  9 Power_On_Hours          -O--CK   099   099   000    -    1680 (71 244 0)
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   099   099   020    -    1472
184 End-to-End_Error        -O--CK   100   100   099    -    0
187 Reported_Uncorrect      -O--CK   086   086   000    -    14
188 Command_Timeout         -O--CK   100   100   000    -    0
189 High_Fly_Writes         -O-RCK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   068   057   045    -    32 (Min/Max 30/32)
191 G-Sense_Error_Rate      -O--CK   100   100   000    -    624
192 Power-Off_Retract_Count -O--CK   100   100   000    -    37
193 Load_Cycle_Count        -O--CK   091   091   000    -    19124
194 Temperature_Celsius     -O---K   032   043   000    -    32 (0 14 0 0 0)
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
240 Head_Flying_Hours       ------   099   099   000    -    1594 (58 173 0)
241 Total_LBAs_Written      ------   100   253   000    -    6252211616
242 Total_LBAs_Read         ------   100   253   000    -    8982026968
254 Free_Fall_Sensor        -O--CK   100   100   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      5  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL     VS    2248  Device vendor specific log
0xa8       GPL,SL  VS      65  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xab       GPL     VS       1  Device vendor specific log
0xb0       GPL     VS    2864  Device vendor specific log
0xbd-0xbf  GPL     VS   65535  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL,SL  VS      10  Device vendor specific log
0xc3       GPL,SL  VS       8  Device vendor specific log
0xc4       GPL,SL  VS      18  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 14
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 14 [13] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 27 00 00  Error: UNC at LBA = 0x04583627 = 72889895

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 14 00 00 07 b4 d2 60 40 00     00:50:04.401  READ FPDMA QUEUED
  60 00 00 00 80 00 00 08 dc ab c8 40 00     00:50:04.401  READ FPDMA QUEUED
  61 00 00 00 08 00 00 05 8a fa 20 40 00     00:50:04.400  WRITE FPDMA QUEUED
  60 00 00 00 04 00 00 07 b4 d2 5c 40 00     00:50:04.399  READ FPDMA QUEUED
  60 00 00 00 22 00 00 07 b4 d2 3a 40 00     00:50:04.399  READ FPDMA QUEUED

Error 13 [12] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 27 00 00  Error: UNC at LBA = 0x04583627 = 72889895

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 01 00 00 04 58 36 27 40 00     00:50:01.749  READ FPDMA QUEUED
  61 00 00 00 08 00 00 00 3a 60 b8 40 00     00:50:01.748  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 36 06 f8 40 00     00:50:01.748  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 08 d7 4d 10 40 00     00:50:01.748  WRITE FPDMA QUEUED
  60 00 00 00 40 00 00 07 63 9d da 40 00     00:50:01.739  READ FPDMA QUEUED

Error 12 [11] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 26 00 00  Error: UNC at LBA = 0x04583626 = 72889894

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 02 00 00 07 b4 c8 30 40 00     00:49:58.994  READ FPDMA QUEUED
  61 00 00 00 08 00 00 00 7f 02 20 40 00     00:49:58.994  WRITE FPDMA QUEUED
  60 00 00 00 01 00 00 04 58 36 26 40 00     00:49:58.994  READ FPDMA QUEUED
  61 00 00 00 68 00 00 00 80 0c 10 40 00     00:49:58.993  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 3a 5f 78 40 00     00:49:58.993  WRITE FPDMA QUEUED

Error 11 [10] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 25 00 00  Error: WP at LBA = 0x04583625 = 72889893

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 30 00 00 00 7f 02 c0 40 00     00:49:56.417  WRITE FPDMA QUEUED
  60 00 00 00 01 00 00 04 58 36 25 40 00     00:49:56.416  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 a0 00     00:49:56.352  FLUSH CACHE EXT
  61 00 00 00 08 00 00 08 d7 4c 38 40 00     00:49:56.274  WRITE FPDMA QUEUED
  61 00 00 00 10 00 00 00 7f 02 38 40 00     00:49:56.274  WRITE FPDMA QUEUED

Error 10 [9] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 25 00 00  Error: UNC at LBA = 0x04583625 = 72889893

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 01 00 00 04 58 36 25 40 00     00:49:53.530  READ FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 14 00 40 00     00:49:53.529  WRITE FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 13 00 40 00     00:49:53.528  WRITE FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 12 00 40 00     00:49:53.527  WRITE FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 11 00 40 00     00:49:53.526  WRITE FPDMA QUEUED

Error 9 [8] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 24 00 00  Error: WP at LBA = 0x04583624 = 72889892

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 20 00 00 00 7f 02 a0 40 00     00:49:50.722  WRITE FPDMA QUEUED
  61 00 00 00 10 00 00 00 82 65 c0 40 00     00:49:50.722  WRITE FPDMA QUEUED
  61 00 00 00 20 00 00 00 82 58 60 40 00     00:49:50.722  WRITE FPDMA QUEUED
  61 00 00 00 60 00 00 00 80 0b b0 40 00     00:49:50.721  WRITE FPDMA QUEUED
  60 00 00 00 80 00 00 08 dd f4 78 40 00     00:49:50.721  READ FPDMA QUEUED

Error 8 [7] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 23 00 00  Error: UNC at LBA = 0x04583623 = 72889891

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 01 00 00 04 58 36 23 40 00     00:49:47.966  READ FPDMA QUEUED
  61 00 00 00 08 00 00 05 8a fc 30 40 00     00:49:47.966  WRITE FPDMA QUEUED
  61 00 00 00 08 00 00 00 3a 5d 70 40 00     00:49:47.966  WRITE FPDMA QUEUED
  60 00 00 00 08 00 00 07 34 f3 30 40 00     00:49:47.965  READ FPDMA QUEUED
  60 00 00 00 68 00 00 07 34 f2 e8 40 00     00:49:47.900  READ FPDMA QUEUED

Error 7 [6] occurred at disk power-on lifetime: 1628 hours (67 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 58 36 22 00 00  Error: WP at LBA = 0x04583622 = 72889890

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 08 00 00 00 3a 5d 18 40 00     00:49:45.181  WRITE FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 04 00 40 00     00:49:45.180  WRITE FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 03 00 40 00     00:49:45.180  WRITE FPDMA QUEUED
  61 00 00 00 70 00 00 00 7f 02 20 40 00     00:49:45.180  WRITE FPDMA QUEUED
  61 00 00 01 00 00 00 02 46 02 00 40 00     00:49:45.179  WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       522 (0x020a)
Device State:                        Active (0)
Current Temperature:                    32 Celsius
Power Cycle Min/Max Temperature:     30/32 Celsius
Lifetime    Min/Max Temperature:     14/42 Celsius
Specified Max Operating Temperature:    33 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        30 minutes
Min/Max recommended Temperature:     14/55 Celsius
Min/Max Temperature Limit:           10/60 Celsius
Temperature History Size (Index):    128 (37)

SCT Error Recovery Control command not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            4  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS

