smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.0-BETA5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Constellation.2 (SATA) Device Model: MM1000GBKAL Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: HPGE User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Nov 24 21:41:33 2023 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 642) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 204) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x103d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 082 063 044 - 182229588 3 Spin_Up_Time PO---- 094 094 070 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 127 5 Reallocated_Sector_Ct PO--CK 095 095 036 - 237 7 Seek_Error_Rate POSR-- 081 060 030 - 140946336 9 Power_On_Hours -O--CK 049 049 000 - 45207 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 126 180 Unknown_HDD_Attribute PO-RCK 100 100 030 - 189036646 184 End-to-End_Error -O--CK 100 100 003 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 076 051 045 - 24 (Min/Max 13/25) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 125 193 Load_Cycle_Count -O--CK 100 100 000 - 1990 194 Temperature_Celsius -O---K 024 049 000 - 24 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 118 099 000 - 182229588 196 Reallocated_Event_Count PO--CK 095 095 036 - 237 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL,SL R/O 1 SATA NCQ Non-Data log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xb6 GPL VS 1918 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 33 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 33 [12] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 18 1e 12 c8 00 00 Error: IDNF at LBA = 0x181e12c8 = 404624072 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 18 1e 12 c8 40 00 3d+15:56:32.197 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 05 80 28 f0 40 00 3d+15:56:32.185 WRITE FPDMA QUEUED 60 00 00 00 60 00 00 23 23 b6 f0 40 00 3d+15:56:32.162 READ FPDMA QUEUED 60 00 00 00 18 00 00 23 23 b6 d8 40 00 3d+15:56:32.162 READ FPDMA QUEUED 61 00 00 00 08 00 00 22 82 54 80 40 00 3d+15:56:32.141 WRITE FPDMA QUEUED Error 32 [11] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 05 80 28 d0 00 00 Error: IDNF at LBA = 0x058028d0 = 92285136 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 05 80 28 d0 40 00 3d+15:56:05.463 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 18 00 57 30 40 00 3d+15:56:05.441 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 05 80 28 d0 40 00 3d+15:56:05.435 WRITE FPDMA QUEUED 61 00 00 00 18 00 00 02 94 5d 80 40 00 3d+15:56:05.429 WRITE FPDMA QUEUED 61 00 00 00 30 00 00 02 94 3a 08 40 00 3d+15:56:05.412 WRITE FPDMA QUEUED Error 31 [10] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 18 1e 5f f8 00 00 Error: IDNF at LBA = 0x181e5ff8 = 404643832 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 28 00 00 18 1e 5f f8 40 00 3d+15:49:58.221 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 02 9f 8b 78 40 00 3d+15:49:58.211 WRITE FPDMA QUEUED 61 00 00 00 50 00 00 24 80 79 a8 40 00 3d+15:49:58.204 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 24 00 31 b8 40 00 3d+15:49:58.196 WRITE FPDMA QUEUED 61 00 00 00 28 00 00 23 80 63 30 40 00 3d+15:49:58.188 WRITE FPDMA QUEUED Error 30 [9] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 18 1e 5f 00 00 00 Error: IDNF at LBA = 0x181e5f00 = 404643584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 18 1e 5f 00 40 00 3d+15:49:38.462 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 18 1e 5e f8 40 00 3d+15:49:38.456 WRITE FPDMA QUEUED 60 00 00 01 c0 00 00 23 19 e2 18 40 00 3d+15:49:38.453 READ FPDMA QUEUED 60 00 00 02 00 00 00 23 19 e0 18 40 00 3d+15:49:38.449 READ FPDMA QUEUED 60 00 00 01 78 00 00 23 19 de 10 40 00 3d+15:49:38.447 READ FPDMA QUEUED Error 29 [8] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 18 1e 58 40 00 00 Error: IDNF at LBA = 0x181e5840 = 404641856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 18 1e 58 40 40 00 3d+15:47:16.912 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 21 30 6e c8 40 00 3d+15:47:16.903 WRITE FPDMA QUEUED 60 00 00 00 c8 00 00 23 30 5b b0 40 00 3d+15:47:16.898 READ FPDMA QUEUED 60 00 00 01 40 00 00 23 30 5a 18 40 00 3d+15:47:16.888 READ FPDMA QUEUED 60 00 00 02 00 00 00 23 30 58 18 40 00 3d+15:47:16.887 READ FPDMA QUEUED Error 28 [7] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 18 1e 57 b8 00 00 Error: IDNF at LBA = 0x181e57b8 = 404641720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 18 1e 57 b8 40 00 3d+15:47:03.849 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 24 80 6d 10 40 00 3d+15:47:03.840 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 24 80 6c f8 40 00 3d+15:47:03.832 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 24 80 6c d8 40 00 3d+15:47:03.821 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 24 00 30 50 40 00 3d+15:47:03.814 WRITE FPDMA QUEUED Error 27 [6] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 23 80 52 d8 00 00 Error: IDNF at LBA = 0x238052d8 = 595612376 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 23 80 52 d8 40 00 3d+15:44:02.266 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 23 33 d0 f8 40 00 3d+15:44:02.260 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 22 83 61 30 40 00 3d+15:44:02.251 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 21 86 d7 c0 40 00 3d+15:44:02.242 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 24 80 5f b8 40 00 3d+15:44:02.213 WRITE FPDMA QUEUED Error 26 [5] occurred at disk power-on lifetime: 44764 hours (1865 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 18 1e 4d d8 00 00 Error: IDNF at LBA = 0x181e4dd8 = 404639192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 18 1e 4d d8 40 00 3d+15:43:21.352 WRITE FPDMA QUEUED 60 00 00 00 48 00 00 23 24 7b a8 40 00 3d+15:43:21.352 READ FPDMA QUEUED 60 00 00 00 20 00 00 23 24 7b f0 40 00 3d+15:43:21.351 READ FPDMA QUEUED 61 00 00 00 08 00 00 22 82 66 08 40 00 3d+15:43:21.343 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 23 24 7a c8 40 00 3d+15:43:21.328 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 44780 - # 2 Short offline Completed without error 00% 44756 - # 3 Short offline Completed without error 00% 44733 - # 4 Short offline Completed without error 00% 44708 - # 5 Short offline Completed without error 00% 44430 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 13/25 Celsius Lifetime Min/Max Temperature: 11/48 Celsius Specified Max Operating Temperature: 60 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (121) SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 126 --- Lifetime Power-On Resets 0x01 0x010 4 45207 --- Power-on Hours 0x01 0x018 6 12607431482 --- Logical Sectors Written 0x01 0x020 6 84209927 --- Number of Write Commands 0x01 0x028 6 55042730696 --- Logical Sectors Read 0x01 0x030 6 200988889 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 45210 --- Spindle Motor Power-on Hours 0x03 0x010 4 45210 --- Head Flying Hours 0x03 0x018 4 1990 --- Head Load Events 0x03 0x020 4 237 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS