smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.1-RELEASE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F2 EG Device Model: SAMSUNG HD103SI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AG01118 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sat Feb 20 08:01:36 2021 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 129 (intermediate), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12740) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 213) minutes. Conveyance self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 085 085 011 - 5380 4 Start_Stop_Count -O--CK 094 094 000 - 6230 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 11429 9 Power_On_Hours -O--CK 099 099 000 - 6090 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5444 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 4 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 078 062 000 - 22 (Min/Max 22/22) 194 Temperature_Celsius -O---K 078 061 000 - 22 (Min/Max 22/22) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 11113 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 69 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL R/O 2 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 2 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 69 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 69 [4] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 50 00 00 00 00 06 1a 88 00 40 00 at LBA = 0x061a8800 = 102402048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:17:31.810 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:15:25.180 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:15:25.180 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:15:25.180 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:15:25.180 READ FPDMA QUEUED Error 68 [3] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 50 00 00 00 00 06 1a 88 00 40 00 at LBA = 0x061a8800 = 102402048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:15:01.820 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:13:21.950 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:13:21.950 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:13:21.950 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:13:21.950 READ FPDMA QUEUED Error 67 [2] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 50 00 00 00 00 06 1a 88 00 40 00 at LBA = 0x061a8800 = 102402048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:13:16.710 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:17.200 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:12:17.200 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:17.200 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:17.200 READ FPDMA QUEUED Error 66 [1] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 50 00 00 00 00 06 1a 88 00 40 00 at LBA = 0x061a8800 = 102402048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:14.100 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:11.820 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:12:11.820 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:11.820 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:12:11.820 READ FPDMA QUEUED Error 65 [0] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 40 00 00 00 00 06 1a 88 00 40 00 at LBA = 0x061a8800 = 102402048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:11:11.150 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:08:40.680 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:08:40.680 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:08:40.680 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:08:40.680 READ FPDMA QUEUED Error 64 [7] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 40 00 00 00 00 06 1a 88 00 40 00 at LBA = 0x061a8800 = 102402048 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:00:36.550 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:00:35.190 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:00:35.190 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:00:35.190 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:00:35.190 READ FPDMA QUEUED Error 63 [6] occurred at disk power-on lifetime: 2924 hours (121 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 40 00 00 00 00 06 1a 88 07 40 00 at LBA = 0x061a8807 = 102402055 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 1a 88 00 40 00 00:51:40.890 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 00 00:51:40.890 FLUSH CACHE EXT 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:41:40.940 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:41:40.940 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:41:40.940 READ FPDMA QUEUED Error 62 [5] occurred at disk power-on lifetime: 2924 hours (121 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 00 00 00 00 00 00 00 40 00 at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 1a 88 00 40 00 00:34:08.400 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 00 00:34:08.400 FLUSH CACHE EXT 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:32:23.980 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 1a 88 00 40 00 00:32:23.980 READ FPDMA QUEUED 60 00 00 00 04 00 00 00 1a 88 40 40 00 00:32:23.980 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 4071 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: --/22 Celsius Lifetime Min/Max Temperature: --/39 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (44) SCT Error Recovery Control: Read: Disabled Write: Disabled ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: Input/output error Read Device Statistics page 0x00 failed Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC