smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.0-RELEASE-p11 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SAMSUNG HD161HJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: JF100-19 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database 7.3/5319 ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Fri May 27 13:12:27 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2891) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 49) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 253 253 025 - 4416 4 Start_Stop_Count -O--CK 087 087 000 - 13551 5 Reallocated_Sector_Ct PO--CK 068 068 010 - 301 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 16596 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 7738 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 1074932 184 End-to-End_Error PO--CK 253 253 099 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 4915200 188 Command_Timeout -O--CK 253 253 000 - 0 190 Airflow_Temperature_Cel -O---K 157 112 000 - 27 (Min/Max 0/42) 194 Temperature_Celsius -O---K 154 109 000 - 28 (Min/Max 0/43) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1074932 196 Reallocated_Event_Count -O--CK 068 068 000 - 301 197 Current_Pending_Sector -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 14 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14 [5] occurred at disk power-on lifetime: 8037 hours (334 days + 21 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 3f 00 40 5c 1c 00 00 00 25 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 00 49d+12:23:10.080 NOP [Abort queued commands] 00 20 16 00 92 00 02 00 0e 01 0b 00 a1 00:00:14.639 NOP [Reserved subcommand] [OBS-ACS-2] Error 13 [4] occurred at disk power-on lifetime: 8037 hours (334 days + 21 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 37 00 40 5c 1c 00 00 00 25 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 00 49d+12:23:10.080 NOP [Abort queued commands] 00 11 89 11 91 00 00 11 06 c9 b1 04 11 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 12 [3] occurred at disk power-on lifetime: 25408 hours (1058 days + 16 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 11 [2] log entry is empty Error 10 [1] log entry is empty Error 9 [0] log entry is empty Error 8 [7] occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 01 e0 cd de 00 00 0c 35 00 at LBA = 0xe0cddf00000c = 247174814236684 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 41 01 00 0c 00 35 00 00 e0 cd dd 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5] 41 01 00 0c 00 35 00 00 e0 cd dc 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5] 41 01 00 0c 00 35 00 00 e0 cd db 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5] 41 01 00 0c 00 35 00 00 e0 cd da 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5] 00 20 16 00 cd 00 02 00 0e 00 0b 00 98 00:00:14.782 NOP [Reserved subcommand] [OBS-ACS-2] Error 7 [6] occurred at disk power-on lifetime: 7296 hours (304 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 7f 00 40 df 6e 00 00 02 25 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 01 00 80 02 87 25 00 00 40 df 6a 00 ff 49d+12:23:10.086 [RESERVED] c3 00 06 00 bf 35 00 00 40 4d 25 00 ff 49d+12:23:10.086 [VENDOR SPECIFIC] c3 00 08 03 17 35 00 00 40 15 69 00 ff 49d+12:23:10.086 [VENDOR SPECIFIC] c3 00 70 02 6f 25 00 00 40 df cd 00 ff 49d+12:23:10.086 [VENDOR SPECIFIC] 00 20 16 00 92 00 02 00 0e 01 0b 00 a1 49d+12:23:24.719 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 14/28 Celsius Lifetime Min/Max Temperature: 0/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (33) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific