smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE-p1 amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F4 EG (AF) Device Model: SAMSUNG HD204UI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AQ10001 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Dec 15 13:34:51 2020 CST ==> WARNING: Using smartmontools or hdparm with this drive may result in data loss due to a firmware bug. ****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ****** Buggy and fixed firmware report same version number! See the following web pages for details: http://knowledge.seagate.com/articles/en_US/FAQ/223571en https://www.smartmontools.org/wiki/SamsungF4EGBadBlocks SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (20820) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 347) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 79 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 066 065 025 - 10435 4 Start_Stop_Count -O--CK 099 099 000 - 1118 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 66156 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1835 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 50318 191 G-Sense_Error_Rate -O---K 096 096 000 - 42276 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 059 000 - 31 (Min/Max 16/45) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 615 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 2023 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 20 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 20 [3] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 5e 19 63 60 40 00 Error: UNC at LBA = 0x5e196360 = 1578722144 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 80 00 00 5e 19 63 00 40 00 00:00:26.865 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 19 63 00 40 00 00:00:26.885 READ FPDMA QUEUED 61 00 03 00 80 00 00 5e 19 62 80 40 00 00:00:26.883 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 19 62 00 40 00 00:00:26.883 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 19 61 80 40 00 00:00:26.883 WRITE FPDMA QUEUED Error 19 [2] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 70 00 00 5e 18 49 90 40 00 Error: UNC at LBA = 0x5e184990 = 1578650000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 80 00 00 5e 18 49 80 40 00 00:00:26.765 READ FPDMA QUEUED 61 00 03 00 80 00 00 5e 18 49 00 40 00 00:00:26.787 WRITE FPDMA QUEUED 60 00 03 00 08 00 00 00 1a 86 c0 40 00 00:00:26.787 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 18 49 80 40 00 00:00:26.787 READ FPDMA QUEUED 61 00 03 00 10 00 00 00 17 e4 10 40 00 00:00:26.786 WRITE FPDMA QUEUED Error 18 [1] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 38 00 00 5e 18 3f c8 40 00 Error: UNC at LBA = 0x5e183fc8 = 1578647496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 80 00 00 5e 18 3f 80 40 00 00:00:26.757 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 18 3f 80 40 00 00:00:26.780 READ FPDMA QUEUED ef 00 03 00 46 00 00 00 00 00 00 00 00 00:00:26.780 SET FEATURES [Set transfer mode] ef 00 03 00 0c 00 00 00 00 00 00 00 00 00:00:26.780 SET FEATURES [Set transfer mode] ef 00 03 00 00 00 00 00 00 00 00 00 00 00:00:26.780 SET FEATURES [Set transfer mode] Error 17 [0] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 38 00 00 5e 18 3f c8 40 00 Error: WP at LBA = 0x5e183fc8 = 1578647496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 03 00 80 00 00 5e 18 3f 00 40 00 00:00:26.779 WRITE FPDMA QUEUED 60 00 03 00 80 00 00 5e 18 3f 80 40 00 00:00:26.755 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 18 3f 80 40 00 00:00:26.774 READ FPDMA QUEUED 61 00 03 00 80 00 00 5e 18 3e 80 40 00 00:00:26.773 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 18 3e 00 40 00 00:00:26.773 WRITE FPDMA QUEUED Error 16 [7] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 30 00 00 5e 17 9d 50 40 00 Error: UNC at LBA = 0x5e179d50 = 1578605904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 80 00 00 5e 17 9d 00 40 00 00:00:26.691 READ FPDMA QUEUED 61 00 03 00 08 00 00 00 18 5a 28 40 00 00:00:26.712 WRITE FPDMA QUEUED 61 00 03 00 10 00 00 00 17 e4 08 40 00 00:00:26.712 WRITE FPDMA QUEUED 60 00 03 00 80 00 00 5e 17 9d 00 40 00 00:00:26.712 READ FPDMA QUEUED 60 00 03 00 08 00 00 00 18 5a 28 40 00 00:00:26.712 READ FPDMA QUEUED Error 15 [6] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 30 00 00 5e 17 9d 50 40 00 Error: UNC at LBA = 0x5e179d50 = 1578605904 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 08 00 00 00 18 5a 28 40 00 00:00:26.711 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 17 9d 00 40 00 00:00:26.687 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 17 9d 00 40 00 00:00:26.707 READ FPDMA QUEUED 61 00 03 00 80 00 00 5e 17 9c 80 40 00 00:00:26.705 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 17 9c 00 40 00 00:00:26.705 WRITE FPDMA QUEUED Error 14 [5] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 38 00 00 5e 16 e9 48 40 00 Error: UNC at LBA = 0x5e16e948 = 1578559816 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 80 00 00 5e 16 e9 00 40 00 00:00:26.617 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 16 e9 00 40 00 00:00:26.639 READ FPDMA QUEUED 61 00 03 00 80 00 00 5e 16 e8 80 40 00 00:00:26.637 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 16 e8 00 40 00 00:00:26.637 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 16 e7 80 40 00 00:00:26.637 WRITE FPDMA QUEUED Error 13 [4] occurred at disk power-on lifetime: 628 hours (26 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 78 00 00 5e 16 3d 08 40 00 Error: UNC at LBA = 0x5e163d08 = 1578515720 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 03 00 80 00 00 5e 16 3d 00 40 00 00:00:26.553 READ FPDMA QUEUED 60 00 03 00 80 00 00 5e 16 3d 00 40 00 00:00:26.572 READ FPDMA QUEUED 61 00 03 00 80 00 00 5e 16 3c 80 40 00 00:00:26.571 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 16 3c 00 40 00 00:00:26.571 WRITE FPDMA QUEUED 61 00 03 00 80 00 00 5e 16 3b 80 40 00 00:00:26.571 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 29449 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 23/34 Celsius Lifetime Min/Max Temperature: 13/65 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (122) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 47 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 48 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific