smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint S250 Device Model: SAMSUNG HD250HJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: FH100-05 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Mon Mar 21 07:05:16 2022 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3697) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 62) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 085 051 - 1 3 Spin_Up_Time POS--- 253 253 025 - 4480 4 Start_Stop_Count -O--CK 081 081 000 - 20028 5 Reallocated_Sector_Ct PO--CK 031 031 010 - 651 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 23353 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 253 000 - 0 12 Power_Cycle_Count -O--CK 090 090 000 - 10230 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 86842 184 End-to-End_Error PO--CK 253 253 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 12662345 188 Command_Timeout -O--CK 253 253 000 - 0 190 Airflow_Temperature_Cel -O---K 157 001 000 - 27 (Min/Max 0/42) 194 Temperature_Celsius -O---K 154 001 000 - 28 (Min/Max 0/42) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 86842 196 Reallocated_Event_Count -O--CK 031 031 000 - 651 197 Current_Pending_Sector -O--C- 090 089 000 - 102 198 Offline_Uncorrectable ----CK 253 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 187 000 - 1 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 080 000 - 0 202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 65535 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 65535 [2] occurred at disk power-on lifetime: 11462 hours (477 days + 14 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 38 ec a0 00 00 c1 00 42 d8 08 00 Device Fault at LBA = 0xc90042d8 = 3372237528 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 46 03 d8 a0 00 ef 00 00 c1 42 00:00:00.000 READ VERIFY SECTOR(S) EXT 00 00 00 00 00 00 00 00 00 00 00 00 00 37d+15:23:39.040 NOP [Abort queued commands] e2 00 80 00 66 00 00 04 00 61 01 03 00 00:00:00.000 STANDBY 94 00 00 08 40 00 e1 01 51 8c 30 11 42 4d+04:48:04.296 STANDBY IMMEDIATE [RET-4] 01 a0 00 fa ec 08 00 42 00 00 b1 30 00 37d+10:50:25.889 [RESERVED] Error 65534 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 66 04 01 e2 00 00 03 00 61 41 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] c5 08 40 01 30 94 00 e1 11 51 8c 80 00 24d+20:31:29.185 WRITE MULTIPLE e1 b0 ec 42 9e 01 08 00 30 00 00 8c a0 01:12:50.813 IDLE IMMEDIATE 00 46 03 00 00 42 b0 a0 9e ef 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] a0 00 00 00 00 00 00 00 00 00 00 00 00 01:12:45.938 PACKET Error 65533 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 30 -- 2c 8c 01 80 11 51 94 00 e1 c7 08 Device Fault at LBA = 0x8011579400e1 = 140811972116705 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 33 42 8d 00 00 e1 01 08 8c 30 00 c8 d8 12d+10:15:41.890 WRITE LONG (w/o retry) [OBS-4] 00 00 00 a0 00 00 42 d8 00 8d ef 00 46 45d+22:45:08.736 NOP [Abort queued commands] 5e 00 00 00 00 a0 00 00 00 00 00 ec 00 13:58:51.714 TRUSTED SEND 00 04 01 00 61 00 e2 00 41 03 00 00 00 00:00:00.000 NOP [Don't abort queued commands] [OBS-ACS-2] a1 01 30 e1 8c c8 94 00 80 11 51 2c 08 19d+19:21:48.800 IDENTIFY PACKET DEVICE Error 65532 [7] occurred at disk power-on lifetime: 5555 hours (231 days + 11 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 d0 00 e0 b6 a7 00 00 0a 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 12 ab 80 00 00 00 0c 01 2e 00 a1 00:00:23.353 NOP [Reserved subcommand] [OBS-ACS-2] Error 65531 [6] occurred at disk power-on lifetime: 7352 hours (306 days + 8 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 80 00 e0 b6 a2 00 00 0a 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f7 00 08 0a 70 25 00 00 e0 b6 a2 00 00 00:00:00.000 [VENDOR SPECIFIC] b8 00 08 0a 68 25 00 00 e0 b6 a2 00 00 00:00:00.000 [RESERVED FOR COMPACTFLASH ASSOCIATION] 7a 00 08 0a 10 25 00 00 e0 5a c8 00 00 00:00:00.000 SEEK [RET-4] 7a 00 08 0a 00 25 00 00 e0 ba c8 00 00 00:00:00.000 SEEK [RET-4] 00 00 12 ab 80 00 00 00 0c 01 2e 00 a1 00:00:23.353 NOP [Reserved subcommand] [OBS-ACS-2] Error 65530 [5] occurred at disk power-on lifetime: 6846 hours (285 days + 6 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 80 00 e0 b6 a2 00 00 0a 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 0b 00 08 0a 70 25 00 00 e0 b6 a2 00 00 00:00:00.000 REQUEST SENSE DATA EXT 4f 00 08 0a 68 25 00 00 e0 b6 a2 00 00 00:00:00.000 [RESERVED] 11 00 08 0a 10 25 00 00 e0 5a c8 00 00 00:00:00.000 RECALIBRATE [RET-4] 11 00 08 0a 00 25 00 00 e0 ba c8 00 00 00:00:00.000 RECALIBRATE [RET-4] 00 00 13 ab 80 00 00 00 0c 01 2e 00 a1 00:00:23.353 NOP [Reserved subcommand] [OBS-ACS-2] Error 65529 [4] occurred at disk power-on lifetime: 6326 hours (263 days + 14 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 08 -- 00 80 00 e0 b6 a2 00 00 0a 25 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- f0 00 08 0a 70 25 00 00 e0 b6 a2 00 00 00:00:00.000 [VENDOR SPECIFIC] b1 00 08 0a 68 25 00 00 e0 b6 a2 00 00 00:00:00.000 DEVICE CONFIGURATION [Reserved subcommand] [OBS-ACS-3] 34 00 08 0a 10 25 00 00 e0 5a c8 00 00 00:00:00.000 WRITE SECTORS(S) EXT 34 00 08 0a 00 25 00 00 e0 ba c8 00 00 00:00:00.000 WRITE SECTORS(S) EXT ff 11 89 11 91 00 00 11 03 c9 b1 04 11 00:00:00.000 [VENDOR SPECIFIC] Error 65528 [3] occurred at disk power-on lifetime: 25408 hours (1058 days + 16 hours) When the command that caused the error occurred, the device was in a reserved state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 15 00 80 00 04 00 68 01 66 00 a1 00:00:16.866 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 26/28 Celsius Lifetime Min/Max Temperature: 0/44 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (56) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific