smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint P80 Device Model: SAMSUNG SP0812C Serial Number: -- Firmware Version: SU100-32 User Capacity: 80,026,361,856 bytes [80.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Mon Jul 3 08:51:31 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 22) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 3000) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 50) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 100 100 025 - 4032 4 Start_Stop_Count -O--CK 100 100 000 - 821 5 Reallocated_Sector_Ct PO--CK 100 100 011 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 0 9 Power_On_Half_Minutes -O--CK 099 099 000 - 5661h+03m 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 508 194 Temperature_Celsius -O---K 154 061 000 - 28 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 76291 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Total_Offl_Uncorrectabl ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 051 - 0 201 Soft_Read_Error_Rate -O-R-- 100 100 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x06 SL R/O 2 SMART self-test log 0x80-0x9f SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 636 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 636 occurred at disk power-on lifetime: 5659 hours (235 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 00:26:02.875 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:26:02.875 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 00:26:02.875 SET FEATURES [Set transfer mode] Error 635 occurred at disk power-on lifetime: 5659 hours (235 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 00:26:02.813 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:26:02.813 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:26:02.563 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00:25:48.625 IDENTIFY DEVICE b0 da 00 00 4f c2 00 00 00:25:48.563 SMART RETURN STATUS Error 634 occurred at disk power-on lifetime: 5659 hours (235 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 00:00:19.125 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:00:19.125 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 00:00:19.125 SET FEATURES [Set transfer mode] Error 633 occurred at disk power-on lifetime: 5659 hours (235 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 00:00:19.125 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:00:19.125 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:00:18.813 NOP [Abort queued commands] 00 00 01 01 00 00 a0 00 00:00:18.750 NOP [Abort queued commands] ec 00 00 00 00 00 00 00 00:00:05.250 IDENTIFY DEVICE Error 632 occurred at disk power-on lifetime: 5658 hours (235 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 06 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 06 00 00 00 00 00 00:01:13.250 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:01:13.250 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 00:01:13.250 SET FEATURES [Set transfer mode] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Abort offline test Aborted by host 60% 0 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported