smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p2 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda Green (AF) Device Model: ST2000DL001-9VT156 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC95 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical (offset 512 bytes) Rotation Rate: 5900 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Oct 7 00:21:22 2022 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 623) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 355) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 094 006 - 87411104 3 Spin_Up_Time PO---- 094 092 000 - 0 4 Start_Stop_Count -O--CK 088 088 020 - 13167 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 087 060 030 - 552913485 9 Power_On_Hours -O--CK 065 065 000 - 31129 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 810 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 1006 188 Command_Timeout -O--CK 100 094 000 - 8590065673 189 High_Fly_Writes -O-RCK 048 048 000 - 52 190 Airflow_Temperature_Cel -O---K 066 043 045 Past 34 (0 117 34 30 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 354 193 Load_Cycle_Count -O--CK 097 097 000 - 7417 194 Temperature_Celsius -O---K 034 057 000 - 34 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 115 099 000 - 87411104 197 Current_Pending_Sector -O--C- 100 090 000 - 0 198 Offline_Uncorrectable ----C- 100 090 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 30732 (100 149 0) 241 Total_LBAs_Written ------ 100 253 000 - 2590073431 242 Total_LBAs_Read ------ 100 253 000 - 1044467196 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5067 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1004 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1004 [3] occurred at disk power-on lifetime: 21704 hours (904 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 13d+09:02:56.389 READ DMA EXT 35 00 00 01 00 00 00 01 32 80 3f e0 00 13d+09:02:56.387 WRITE DMA EXT 35 00 00 01 00 00 00 01 32 7f 3f e0 00 13d+09:02:56.387 WRITE DMA EXT 25 00 00 01 00 00 00 01 31 c6 3f e0 00 13d+09:02:56.386 READ DMA EXT 25 00 00 01 00 00 00 01 31 c5 3f e0 00 13d+09:02:56.385 READ DMA EXT Error 1003 [2] occurred at disk power-on lifetime: 21704 hours (904 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 13d+09:02:10.884 READ DMA EXT 35 00 00 01 00 00 00 01 31 c6 3f e0 00 13d+09:02:10.883 WRITE DMA EXT 35 00 00 01 00 00 00 01 31 c5 3f e0 00 13d+09:02:10.882 WRITE DMA EXT 25 00 00 01 00 00 00 01 31 0b 3f e0 00 13d+09:02:10.881 READ DMA EXT 35 00 00 01 00 00 00 01 31 c4 3f e0 00 13d+09:02:10.879 WRITE DMA EXT Error 1002 [1] occurred at disk power-on lifetime: 21704 hours (904 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 13d+09:01:22.761 READ DMA EXT 35 00 00 01 00 00 00 01 31 0c 3f e0 00 13d+09:01:22.760 WRITE DMA EXT 35 00 00 01 00 00 00 01 31 0b 3f e0 00 13d+09:01:22.759 WRITE DMA EXT 25 00 00 01 00 00 00 01 30 42 3f e0 00 13d+09:01:22.758 READ DMA EXT 25 00 00 01 00 00 00 01 30 41 3f e0 00 13d+09:01:22.588 READ DMA EXT Error 1001 [0] occurred at disk power-on lifetime: 21704 hours (904 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 13d+09:00:15.372 READ DMA EXT 35 00 00 01 00 00 00 01 30 42 3f e0 00 13d+09:00:15.371 WRITE DMA EXT 35 00 00 01 00 00 00 01 30 41 3f e0 00 13d+09:00:15.370 WRITE DMA EXT 25 00 00 01 00 00 00 08 57 2b 8f e0 00 13d+09:00:15.369 READ DMA EXT 25 00 00 01 00 00 00 08 57 2a 8f e0 00 13d+09:00:15.360 READ DMA EXT Error 1000 [19] occurred at disk power-on lifetime: 21704 hours (904 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 13d+08:31:41.325 READ DMA EXT 35 00 00 01 00 00 00 08 57 2b 8f e0 00 13d+08:31:41.324 WRITE DMA EXT 35 00 00 01 00 00 00 08 57 2a 8f e0 00 13d+08:31:41.323 WRITE DMA EXT 25 00 00 01 00 00 00 0c ca eb 5f e0 00 13d+08:31:41.322 READ DMA EXT 25 00 00 01 00 00 00 0c ca ea 5f e0 00 13d+08:31:41.142 READ DMA EXT Error 999 [18] occurred at disk power-on lifetime: 21590 hours (899 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 8d+14:25:31.499 READ DMA EXT 35 00 00 01 00 00 00 0c ca eb 5f e0 00 8d+14:25:31.497 WRITE DMA EXT 35 00 00 01 00 00 00 0c ca ea 5f e0 00 8d+14:25:31.496 WRITE DMA EXT 25 00 00 01 00 00 00 0c ca 30 5f e0 00 8d+14:25:31.495 READ DMA EXT 35 00 00 01 00 00 00 0c ca e9 5f e0 00 8d+14:25:31.492 WRITE DMA EXT Error 998 [17] occurred at disk power-on lifetime: 21590 hours (899 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 8d+14:24:45.794 READ DMA EXT 35 00 00 01 00 00 00 0c ca 31 5f e0 00 8d+14:24:45.793 WRITE DMA EXT 35 00 00 01 00 00 00 0c ca 30 5f e0 00 8d+14:24:45.792 WRITE DMA EXT 25 00 00 01 00 00 00 0c c9 77 5f e0 00 8d+14:24:45.791 READ DMA EXT 25 00 00 01 00 00 00 0c c9 76 5f e0 00 8d+14:24:45.615 READ DMA EXT Error 997 [16] occurred at disk power-on lifetime: 21590 hours (899 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 48 36 d8 0f 00 00 Error: UNC at LBA = 0x4836d80f = 1211553807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 48 36 d7 ff e0 00 8d+14:24:05.217 READ DMA EXT 35 00 00 01 00 00 00 0c c9 77 5f e0 00 8d+14:24:05.214 WRITE DMA EXT 35 00 00 01 00 00 00 0c c9 76 5f e0 00 8d+14:24:05.213 WRITE DMA EXT 25 00 00 01 00 00 00 0c c8 bc 5f e0 00 8d+14:24:05.211 READ DMA EXT 35 00 00 01 00 00 00 0c c9 75 5f e0 00 8d+14:24:05.209 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 30/34 Celsius Lifetime Min/Max Temperature: 16/57 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (75) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS