smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p11 amd64] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda Green (AF) Device Model: ST2000DL003-9VT166 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC32 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Jul 27 08:48:36 2020 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 0 (vendor specific), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 623) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 340) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30b7) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 109 099 006 - 24936648 3 Spin_Up_Time PO---- 093 091 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1881 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 072 060 030 - 30220980280 9 Power_On_Hours -O--CK 045 045 000 - 48388 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1890 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 098 098 000 - 2 188 Command_Timeout -O--CK 100 099 000 - 1 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 052 045 - 37 (Min/Max 27/41) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1841 193 Load_Cycle_Count -O--CK 100 100 000 - 1954 194 Temperature_Celsius -O---K 037 048 000 - 37 (0 17 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 013 004 000 - 24936648 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 48237 (200 55 0) 241 Total_LBAs_Written ------ 100 253 000 - 491701197 242 Total_LBAs_Read ------ 100 253 000 - 2106470736 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 15 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 15 [14] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c7 00 00 Error: UNC at LBA = 0xc385f0c7 = 3280335047 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:31.810 READ FPDMA QUEUED 60 00 00 00 10 00 00 03 56 b4 e0 40 00 22:15:31.672 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c6 40 00 22:15:31.672 WRITE FPDMA QUEUED 60 00 00 00 10 00 00 03 56 7d 90 40 00 22:15:31.671 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:31.633 CHECK POWER MODE Error 14 [13] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c7 00 00 Error: UNC at LBA = 0xc385f0c7 = 3280335047 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:31.810 READ FPDMA QUEUED 60 00 00 00 10 00 00 03 56 b4 e0 40 00 22:15:31.672 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c6 40 00 22:15:31.672 WRITE FPDMA QUEUED 60 00 00 00 10 00 00 03 56 7d 90 40 00 22:15:31.671 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:31.633 CHECK POWER MODE Error 13 [12] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c6 00 00 Error: UNC at LBA = 0xc385f0c6 = 3280335046 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:31.194 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c5 40 00 22:15:31.022 WRITE FPDMA QUEUED 60 00 00 00 10 00 00 03 56 05 00 40 00 22:15:31.021 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:30.988 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 00 22:15:30.880 READ LOG EXT Error 12 [11] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c6 00 00 Error: UNC at LBA = 0xc385f0c6 = 3280335046 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:31.194 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c5 40 00 22:15:31.022 WRITE FPDMA QUEUED 60 00 00 00 10 00 00 03 56 05 00 40 00 22:15:31.021 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:30.988 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 00 22:15:30.880 READ LOG EXT Error 11 [10] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c5 00 00 Error: UNC at LBA = 0xc385f0c5 = 3280335045 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:30.558 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c4 40 00 22:15:30.421 WRITE FPDMA QUEUED 60 00 00 04 00 00 00 03 55 fc 00 40 00 22:15:30.421 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:30.391 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 00 22:15:30.284 READ LOG EXT Error 10 [9] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c5 00 00 Error: UNC at LBA = 0xc385f0c5 = 3280335045 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:30.558 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c4 40 00 22:15:30.421 WRITE FPDMA QUEUED 60 00 00 04 00 00 00 03 55 fc 00 40 00 22:15:30.421 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:30.391 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 00 22:15:30.284 READ LOG EXT Error 9 [8] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c4 00 00 Error: UNC at LBA = 0xc385f0c4 = 3280335044 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:29.962 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c3 40 00 22:15:29.803 WRITE FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:29.776 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 00 22:15:29.668 READ LOG EXT 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:29.285 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 30045 hours (1251 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c3 85 f0 c4 00 00 Error: UNC at LBA = 0xc385f0c4 = 3280335044 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:29.962 READ FPDMA QUEUED 61 00 00 00 01 00 00 c3 85 f0 c3 40 00 22:15:29.803 WRITE FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 00 22:15:29.776 CHECK POWER MODE 2f 00 00 00 01 00 00 00 00 00 10 00 00 22:15:29.668 READ LOG EXT 60 00 00 04 00 00 00 c3 85 f0 00 40 00 22:15:29.285 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 48379 - # 2 Extended offline Completed without error 00% 48361 - # 3 Short offline Completed without error 00% 48331 - # 4 Short offline Completed without error 00% 48307 - # 5 Short offline Completed without error 00% 48283 - # 6 Short offline Completed without error 00% 48259 - # 7 Short offline Completed without error 00% 48235 - # 8 Short offline Completed without error 00% 48211 - # 9 Extended offline Completed without error 00% 48192 - #10 Short offline Completed without error 00% 48163 - #11 Short offline Completed without error 00% 48139 - #12 Short offline Completed without error 00% 48115 - #13 Short offline Completed without error 00% 48091 - #14 Short offline Completed without error 00% 48067 - #15 Short offline Completed without error 00% 48043 - #16 Extended offline Completed without error 00% 48024 - #17 Short offline Completed without error 00% 47995 - #18 Short offline Completed without error 00% 47971 - #19 Short offline Completed without error 00% 47947 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 27/41 Celsius Lifetime Min/Max Temperature: 17/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (81) SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 44 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS