smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.0-RELEASE amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Desktop SSHD Device Model: ST2000DX001-1CM164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC62 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon May 20 19:59:51 2024 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 223) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1081) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 099 006 - 192115456 3 Spin_Up_Time PO---- 096 095 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5290 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 4545903575 9 Power_On_Hours -O--CK 065 065 000 - 30979 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5174 183 Runtime_Bad_Block -O--CK 060 060 000 - 40 184 End-to-End_Error -O--CK 095 095 099 NOW 5 187 Reported_Uncorrect -O--CK 099 099 000 - 1 188 Command_Timeout -O--CK 100 099 000 - 1 91 98 189 High_Fly_Writes -O-RCK 097 097 000 - 3 190 Airflow_Temperature_Cel -O---K 063 050 045 - 37 (Min/Max 37/38) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1943 193 Load_Cycle_Count -O--CK 095 095 000 - 11302 194 Temperature_Celsius -O---K 037 050 000 - 37 (0 10 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 34293h+34m+39.261s 241 Total_LBAs_Written ------ 100 253 000 - 35105156805 242 Total_LBAs_Read ------ 100 253 000 - 60801282201 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 3900 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4580 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 27380 hours (1140 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 1e 90 a4 00 00 Error: UNC at LBA = 0x001e90a4 = 2003108 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 1e 90 80 40 00 00:00:17.539 READ DMA EXT 25 00 00 00 40 00 00 00 1f b8 80 40 00 00:00:17.538 READ DMA EXT 25 00 00 00 40 00 00 00 20 66 80 40 00 00:00:17.537 READ DMA EXT 25 00 00 00 40 00 00 00 20 4d c0 40 00 00:00:17.536 READ DMA EXT 25 00 00 00 40 00 00 08 3f b8 00 40 00 00:00:17.535 READ DMA EXT Error 5 [4] occurred at disk power-on lifetime: 27380 hours (1140 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 1e 90 9a 00 00 Error: UNC at LBA = 0x001e909a = 2003098 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 1e 90 80 40 00 00:00:17.234 READ DMA EXT 25 00 00 00 40 00 00 00 1e 90 40 40 00 00:00:17.218 READ DMA EXT 25 00 00 00 40 00 00 dc ac 92 80 40 00 00:00:17.217 READ DMA EXT 25 00 00 00 40 00 00 dc ab 95 80 40 00 00:00:17.216 READ DMA EXT 25 00 00 00 40 00 00 dc ab 88 40 40 00 00:00:17.215 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 27380 hours (1140 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 1e 90 04 00 00 Error: UNC at LBA = 0x001e9004 = 2002948 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 dc ab 88 00 40 00 2d+02:45:09.279 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 1e 90 00 40 00 2d+02:45:09.279 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 00 08 00 40 00 2d+02:45:09.279 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 00 00 00 40 00 2d+02:45:09.279 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 2d+02:45:09.156 FLUSH CACHE EXT Error 3 [2] occurred at disk power-on lifetime: 27179 hours (1132 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 3f db 40 00 00 Error: UNC at LBA = 0x033fdb40 = 54516544 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 07 d8 00 00 03 3f c0 28 40 00 00:39:00.993 READ FPDMA QUEUED 60 00 00 05 e0 00 00 03 3f c8 00 40 00 00:39:00.993 READ FPDMA QUEUED 60 00 00 0a 00 00 00 03 3f d1 e0 40 00 00:39:00.993 READ FPDMA QUEUED 60 00 00 0a 00 00 00 03 3f db e0 40 00 00:39:00.993 READ FPDMA QUEUED 60 00 00 02 20 00 00 03 3f e5 e0 40 00 00:39:00.993 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 26459 hours (1102 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 1e 90 c4 00 00 Error: UNC at LBA = 0x001e90c4 = 2003140 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 dc ab 88 00 40 00 19:38:04.989 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 1e 90 00 40 00 19:38:04.989 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 00 08 00 40 00 19:38:04.989 READ FPDMA QUEUED 60 00 00 01 00 00 00 00 00 00 00 40 00 19:38:04.989 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 19:38:04.866 FLUSH CACHE EXT Error 1 [0] occurred at disk power-on lifetime: 15679 hours (653 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 16 74 16 00 00 Error: UNC at LBA = 0x01167416 = 18248726 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 02 00 00 01 32 d2 27 40 00 01:27:22.828 READ FPDMA QUEUED 61 00 00 00 08 00 00 06 fc ac 78 40 00 01:27:22.828 WRITE FPDMA QUEUED 61 00 00 00 28 00 00 01 5d 8e 18 40 00 01:27:22.719 WRITE FPDMA QUEUED 61 00 00 00 60 00 00 06 fd 15 88 40 00 01:27:22.718 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 04 1b dd c0 40 00 01:27:22.718 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 30866 - # 2 Extended offline Completed without error 00% 29309 - # 3 Extended offline Completed without error 00% 29191 - # 4 Extended offline Completed without error 00% 28611 - # 5 Extended offline Completed without error 00% 23192 - # 6 Extended offline Completed without error 00% 22884 - # 7 Extended offline Completed without error 00% 22743 - # 8 Extended offline Interrupted (host reset) 00% 22590 - # 9 Short offline Interrupted (host reset) 00% 15677 - #10 Short offline Completed without error 00% 1408 - #11 Vendor (0x50) Completed without error 00% 1383 - #12 Short offline Completed without error 00% 1383 - #13 Vendor (0x50) Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 25/38 Celsius Lifetime Min/Max Temperature: 14/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 19 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS