smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST31000333AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SD35 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Mar 31 02:42:52 2021 EDT ==> WARNING: There are known problems with these drives, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/207951en http://knowledge.seagate.com/articles/en_US/FAQ/207957en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 625) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 208) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 115 099 006 - 86949018 3 Spin_Up_Time PO---- 093 091 000 - 0 4 Start_Stop_Count -O--CK 090 090 020 - 10482 5 Reallocated_Sector_Ct PO--CK 099 099 036 - 78 7 Seek_Error_Rate POSR-- 084 060 030 - 237682045 9 Power_On_Hours -O--CK 092 092 000 - 7687 10 Spin_Retry_Count PO--C- 100 100 097 - 84 12 Power_Cycle_Count -O--CK 092 037 020 - 9138 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 095 095 000 - 5 188 Command_Timeout -O--CK 100 098 000 - 17182228567 189 High_Fly_Writes -O-RCK 001 001 000 - 2226 190 Airflow_Temperature_Cel -O---K 067 044 045 Past 33 (0 40 33 19 0) 194 Temperature_Celsius -O---K 033 056 000 - 33 (0 10 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 040 021 000 - 86949018 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 7455 hours (310 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 50 00 85 26 00 00 Error: UNC at LBA = 0x1750008526 = 100126459174 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:33.602 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:29.579 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:25.485 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 60 40 00 00:02:25.481 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:21.796 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 7455 hours (310 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 50 00 85 26 00 00 Error: UNC at LBA = 0x1750008526 = 100126459174 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:29.579 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:25.485 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 60 40 00 00:02:25.481 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:21.796 READ DMA EXT 25 00 00 00 08 00 00 33 00 b3 98 40 00 00:02:21.658 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 7455 hours (310 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 50 00 85 26 00 00 Error: UNC at LBA = 0x1750008526 = 100126459174 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:25.485 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 60 40 00 00:02:25.481 READ DMA EXT 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:21.796 READ DMA EXT 25 00 00 00 08 00 00 33 00 b3 98 40 00 00:02:21.658 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:02:21.573 READ LOG EXT Error 2 [1] occurred at disk power-on lifetime: 7455 hours (310 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 50 00 85 26 00 00 Error: UNC at LBA = 0x1750008526 = 100126459174 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 17 50 00 85 20 40 00 00:02:21.796 READ DMA EXT 25 00 00 00 08 00 00 33 00 b3 98 40 00 00:02:21.658 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 00:02:21.573 READ LOG EXT 60 00 00 00 08 00 00 33 00 b3 98 40 00 00:02:17.873 READ FPDMA QUEUED 60 00 00 00 08 00 00 45 00 b3 10 40 00 00:02:17.870 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 7455 hours (310 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 17 50 00 85 26 00 00 Error: UNC at LBA = 0x1750008526 = 100126459174 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 33 00 b3 98 40 00 00:02:17.873 READ FPDMA QUEUED 60 00 00 00 08 00 00 45 00 b3 10 40 00 00:02:17.870 READ FPDMA QUEUED 60 00 00 00 08 00 00 5a 00 b3 40 40 00 00:02:17.864 READ FPDMA QUEUED 60 00 00 00 08 00 00 44 00 b3 70 40 00 00:02:17.864 READ FPDMA QUEUED 60 00 00 00 08 00 00 32 00 b4 a0 40 00 00:02:17.864 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7330 - # 2 Extended offline Aborted by host 90% 7330 - # 3 Short offline Completed without error 00% 6773 - # 4 Extended offline Interrupted (host reset) 00% 6074 - # 5 Short offline Aborted by host 90% 1772 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 19/32 Celsius Lifetime Min/Max Temperature: 10/56 Celsius Under/Over Temperature Limit Count: 0/29 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (61) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS