smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.0-RELEASE-p12 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba MG05ACA... Enterprise Capacity HDD Device Model: TOSHIBA MG05ACA800E Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: GX1A User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.2/5254 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Aug 14 12:34:24 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 112) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 745) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 090 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 7690 4 Start_Stop_Count -O--CK 100 100 000 - 51 5 Reallocated_Sector_Ct PO--CK 003 003 050 NOW 16336 (0 1) 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 014 014 000 - 34448 10 Spin_Retry_Count PO--CK 101 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 50 191 G-Sense_Error_Rate -O--CK 100 100 000 - 1 192 Power-Off_Retract_Count -O--CK 100 100 000 - 36 193 Load_Cycle_Count -O--CK 100 100 000 - 57 194 Temperature_Celsius -O---K 100 100 000 - 38 (Min/Max 14/52) 196 Reallocated_Event_Count -O--CK 100 100 000 - 8499 197 Current_Pending_Sector -O--CK 100 100 000 - 48 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 26 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 018 018 000 - 33121 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 569 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 2 Device Statistics Notification 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 16384 Current Device Internal Status Data log 0x25 GPL R/O 16384 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 4960 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4960 [95] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 a8 00 00 2e be c9 b0 40 00 Error: WP at LBA = 0x2ebec9b0 = 784255408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 18 00 01 9d ba 33 f8 40 00 3d+08:26:38.820 WRITE FPDMA QUEUED 61 00 10 00 10 00 01 9d ba 33 c8 40 00 3d+08:26:38.819 WRITE FPDMA QUEUED 61 00 10 00 08 00 01 9d b6 c4 58 40 00 3d+08:26:38.819 WRITE FPDMA QUEUED 61 00 10 00 00 00 01 9d b6 c4 28 40 00 3d+08:26:38.819 WRITE FPDMA QUEUED 61 00 10 00 f8 00 01 9d b6 c3 e8 40 00 3d+08:26:38.819 WRITE FPDMA QUEUED Error 4959 [94] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 90 00 00 2e be c9 c8 40 00 Error: WP at LBA = 0x2ebec9c8 = 784255432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 98 00 01 9d cd a6 f8 40 00 3d+08:26:32.104 WRITE FPDMA QUEUED 61 00 10 00 88 00 01 9d ba 34 58 40 00 3d+08:26:32.104 WRITE FPDMA QUEUED 61 00 10 00 80 00 01 9d ba 34 38 40 00 3d+08:26:32.103 WRITE FPDMA QUEUED 61 00 10 00 78 00 01 9d ba 34 18 40 00 3d+08:26:32.103 WRITE FPDMA QUEUED 61 00 10 00 70 00 01 9f 2d a1 18 40 00 3d+08:26:32.103 WRITE FPDMA QUEUED Error 4958 [93] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 38 00 00 2e be cb 28 40 00 Error: UNC at LBA = 0x2ebecb28 = 784255784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 40 00 01 85 7c 27 d8 40 00 3d+08:26:20.214 READ FPDMA QUEUED 60 08 00 00 38 00 00 2e be c8 08 40 00 3d+08:26:20.214 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+08:26:20.214 READ LOG EXT 60 00 10 00 28 00 01 85 7c 27 d8 40 00 3d+08:26:13.501 READ FPDMA QUEUED 61 00 10 00 20 00 01 9f 2d a0 e8 40 00 3d+08:26:13.501 WRITE FPDMA QUEUED Error 4957 [92] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 2e be c9 c0 40 00 Error: UNC at LBA = 0x2ebec9c0 = 784255424 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 28 00 01 85 7c 27 d8 40 00 3d+08:26:13.501 READ FPDMA QUEUED 61 00 10 00 20 00 01 9f 2d a0 e8 40 00 3d+08:26:13.501 WRITE FPDMA QUEUED 61 00 50 00 18 00 01 9f 2d a0 28 40 00 3d+08:26:13.500 WRITE FPDMA QUEUED 61 00 e0 00 10 00 01 9d e0 a8 18 40 00 3d+08:26:13.500 WRITE FPDMA QUEUED 61 00 40 00 08 00 01 9d e0 a0 18 40 00 3d+08:26:13.500 WRITE FPDMA QUEUED Error 4956 [91] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 88 00 00 2e be c9 c0 40 00 Error: UNC at LBA = 0x2ebec9c0 = 784255424 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 06 80 00 98 00 02 28 d0 5a 88 40 00 3d+08:26:04.494 READ FPDMA QUEUED 60 00 10 00 90 00 00 ff 26 20 08 40 00 3d+08:26:04.494 READ FPDMA QUEUED 60 08 00 00 88 00 00 2e be c8 08 40 00 3d+08:26:04.494 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+08:26:04.494 READ LOG EXT 60 06 80 00 78 00 02 28 d0 5a 88 40 00 3d+08:26:03.931 READ FPDMA QUEUED Error 4955 [90] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 68 00 00 2e be c9 c0 40 00 Error: UNC at LBA = 0x2ebec9c0 = 784255424 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 06 80 00 78 00 02 28 d0 5a 88 40 00 3d+08:26:03.931 READ FPDMA QUEUED 60 00 10 00 70 00 00 ff 26 20 08 40 00 3d+08:25:57.191 READ FPDMA QUEUED 60 08 00 00 68 00 00 2e be c8 08 40 00 3d+08:25:57.191 READ FPDMA QUEUED 60 00 e0 00 60 00 02 ff ff fe 28 40 00 3d+08:25:57.190 READ FPDMA QUEUED 60 00 e0 00 58 00 02 ff ff fc 28 40 00 3d+08:25:57.189 READ FPDMA QUEUED Error 4954 [89] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 d8 00 00 2e be c9 b0 40 00 Error: UNC at LBA = 0x2ebec9b0 = 784255408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 00 00 d8 00 00 2e be c8 08 40 00 3d+08:25:52.911 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+08:25:52.910 READ LOG EXT 60 08 00 00 c8 00 00 2e be c8 08 40 00 3d+08:25:48.195 READ FPDMA QUEUED 61 00 10 00 c0 00 02 ff ff fe 18 40 00 3d+08:25:48.063 WRITE FPDMA QUEUED 61 00 10 00 b8 00 02 ff ff fc 18 40 00 3d+08:25:48.061 WRITE FPDMA QUEUED Error 4953 [88] occurred at disk power-on lifetime: 34438 hours (1434 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 c8 00 00 2e be c9 b0 40 00 Error: UNC at LBA = 0x2ebec9b0 = 784255408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 00 00 c8 00 00 2e be c8 08 40 00 3d+08:25:48.195 READ FPDMA QUEUED 61 00 10 00 c0 00 02 ff ff fe 18 40 00 3d+08:25:48.063 WRITE FPDMA QUEUED 61 00 10 00 b8 00 02 ff ff fc 18 40 00 3d+08:25:48.061 WRITE FPDMA QUEUED 60 06 80 00 b0 00 00 7b 73 2d 08 40 00 3d+08:25:48.049 READ FPDMA QUEUED 60 06 80 00 a8 00 00 7b 73 2d 08 40 00 3d+08:25:48.038 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 00% 28063 346656 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 29/43 Celsius Lifetime Min/Max Temperature: 14/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (254) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 50 --- Lifetime Power-On Resets 0x01 0x010 4 34448 --- Power-on Hours 0x01 0x018 6 115483768366 --- Logical Sectors Written 0x01 0x020 6 1245221195 --- Number of Write Commands 0x01 0x028 6 1979267533500 --- Logical Sectors Read 0x01 0x030 6 3694321503 --- Number of Read Commands 0x01 0x038 6 124013134892 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 1 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 34447 --- Spindle Motor Power-on Hours 0x03 0x010 4 33121 --- Head Flying Hours 0x03 0x018 4 57 --- Head Load Events 0x03 0x020 4 81872 -D- Number of Reallocated Logical Sectors 0x03 0x028 4 1470695 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 48 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 36 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 4933 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 806 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x010 1 38 N-- Average Short Term Temperature 0x05 0x018 1 34 N-- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x030 1 45 N-- Highest Average Short Term Temperature 0x05 0x038 1 20 N-- Lowest Average Short Term Temperature 0x05 0x040 1 38 N-- Highest Average Long Term Temperature 0x05 0x048 1 21 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2522 --- Number of Hardware Resets 0x06 0x010 4 284 --- Number of ASR Events 0x06 0x018 4 26 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) Index LBA Hours 0 574749120 - 1 574749121 - 2 574749122 - 3 574749123 - 4 574749124 - 5 574749125 - 6 574749126 - 7 574749127 - 8 574983192 - 9 574983193 - 10 574983194 - 11 574983195 - 12 574983196 - 13 574983197 - 14 574983198 - 15 574983199 - 16 575113880 - 17 575113881 - 18 575113882 - 19 575113883 - 20 575113884 - 21 575113885 - 22 575113886 - 23 575113887 - 24 591823800 - 25 591823801 - 26 591823802 - 27 591823803 - 28 591823804 - 29 591823805 - 30 591823806 - ... (17 entries not shown) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 12 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC