smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.1-RELEASE-p9 i386] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 2.5" HDD (10-20 GB) Device Model: TOSHIBA MK2018GAP Serial Number: -- Firmware Version: M1.42 A User Capacity: 20,003,880,960 bytes [20.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-5 (minor revision not indicated) Local Time is: Wed Sep 16 23:09:11 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 212) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 24) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 979 4 Start_Stop_Count -O--CK 100 100 000 - 1340 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 31 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 093 093 000 - 3037 10 Spin_Retry_Count PO--CK 126 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1334 192 Power-Off_Retract_Count -O--CK 100 100 000 - 64 193 Load_Cycle_Count -O--CK 089 089 000 - 118941 196 Reallocated_Event_Count -O--CK 100 100 000 - 19 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 4200 222 Loaded_Hours -O--CK 096 096 000 - 1880 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 353 240 Head_Flying_Hours P----- 100 100 001 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: Input/output error General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 212 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 212 occurred at disk power-on lifetime: 2914 hours (121 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 4a b7 e1 Error: UNC at LBA = 0x01b74a08 = 28789256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 80 8f 49 b7 e1 00 00:23:25.810 READ VERIFY SECTOR(S) 40 00 90 7f 49 b7 e1 00 00:23:16.981 READ VERIFY SECTOR(S) 40 00 a0 6f 49 b7 e1 00 00:23:08.152 READ VERIFY SECTOR(S) 40 00 b0 5f 49 b7 e1 00 00:22:59.352 READ VERIFY SECTOR(S) 40 00 c0 4f 49 b7 e1 00 00:22:50.581 READ VERIFY SECTOR(S) Error 211 occurred at disk power-on lifetime: 2914 hours (121 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 4a b7 e1 Error: UNC at LBA = 0x01b74a08 = 28789256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 90 7f 49 b7 e1 00 00:23:16.981 READ VERIFY SECTOR(S) 40 00 a0 6f 49 b7 e1 00 00:23:08.152 READ VERIFY SECTOR(S) 40 00 b0 5f 49 b7 e1 00 00:22:59.352 READ VERIFY SECTOR(S) 40 00 c0 4f 49 b7 e1 00 00:22:50.581 READ VERIFY SECTOR(S) 40 00 d0 3f 49 b7 e1 00 00:22:41.765 READ VERIFY SECTOR(S) Error 210 occurred at disk power-on lifetime: 2914 hours (121 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 4a b7 e1 Error: UNC at LBA = 0x01b74a08 = 28789256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 a0 6f 49 b7 e1 00 00:23:08.152 READ VERIFY SECTOR(S) 40 00 b0 5f 49 b7 e1 00 00:22:59.352 READ VERIFY SECTOR(S) 40 00 c0 4f 49 b7 e1 00 00:22:50.581 READ VERIFY SECTOR(S) 40 00 d0 3f 49 b7 e1 00 00:22:41.765 READ VERIFY SECTOR(S) 40 00 f0 1f 4a b7 e1 00 00:22:41.738 READ VERIFY SECTOR(S) Error 209 occurred at disk power-on lifetime: 2914 hours (121 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 4a b7 e1 Error: UNC at LBA = 0x01b74a08 = 28789256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 b0 5f 49 b7 e1 00 00:22:59.352 READ VERIFY SECTOR(S) 40 00 c0 4f 49 b7 e1 00 00:22:50.581 READ VERIFY SECTOR(S) 40 00 d0 3f 49 b7 e1 00 00:22:41.765 READ VERIFY SECTOR(S) 40 00 f0 1f 4a b7 e1 00 00:22:41.738 READ VERIFY SECTOR(S) 40 00 10 ff 49 b7 e1 00 00:22:32.938 READ VERIFY SECTOR(S) Error 208 occurred at disk power-on lifetime: 2914 hours (121 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 08 4a b7 e1 Error: UNC at LBA = 0x01b74a08 = 28789256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 00 c0 4f 49 b7 e1 00 00:22:50.581 READ VERIFY SECTOR(S) 40 00 d0 3f 49 b7 e1 00 00:22:41.765 READ VERIFY SECTOR(S) 40 00 f0 1f 4a b7 e1 00 00:22:41.738 READ VERIFY SECTOR(S) 40 00 10 ff 49 b7 e1 00 00:22:32.938 READ VERIFY SECTOR(S) 40 00 30 df 49 b7 e1 00 00:22:24.109 READ VERIFY SECTOR(S) SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported