smartctl 7.3 2022-02-28 r5338 [OpenBSD 7.2 amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 2.5" HDD MK..75GSX Device Model: TOSHIBA MK6475GSX Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: GT001M User Capacity: 640,135,028,736 bytes [640 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Dec 23 22:21:13 2022 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 207) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1337 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 8126 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 8 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 11864 10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7882 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 3900 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 745 193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 44267 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 41 (Min/Max 9/65) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 86 222 Loaded_Hours 0x0032 074 074 000 Old_age Always - 10749 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 237 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 114 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 114 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 7a d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 80 88 d8 3b 01 40 00 02:06:37.514 READ FPDMA QUEUED 60 30 80 58 b1 f9 40 00 02:06:37.514 READ FPDMA QUEUED 60 40 78 c8 b1 c4 40 00 02:06:37.514 READ FPDMA QUEUED 60 40 70 ca e6 31 40 00 02:06:37.514 READ FPDMA QUEUED 60 28 60 f0 c2 88 40 00 02:06:37.514 READ FPDMA QUEUED Error 113 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 22 d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 68 18 50 77 31 40 00 02:06:26.061 READ FPDMA QUEUED 60 08 08 30 60 03 40 00 02:06:26.056 READ FPDMA QUEUED 60 40 10 f2 2a d4 40 00 02:06:26.049 READ FPDMA QUEUED 60 20 18 8b a4 ff 40 00 02:06:26.045 READ FPDMA QUEUED 60 08 30 20 66 bc 40 00 02:06:26.045 READ FPDMA QUEUED Error 112 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 6a d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 18 70 28 54 e1 40 00 02:05:26.484 READ FPDMA QUEUED 60 20 18 da b0 ff 40 00 02:05:26.480 READ FPDMA QUEUED 60 08 68 d0 b1 c4 40 00 02:05:26.474 READ FPDMA QUEUED 60 08 60 20 66 bc 40 00 02:05:26.473 READ FPDMA QUEUED 60 40 50 f2 2a d4 40 00 02:05:26.473 READ FPDMA QUEUED Error 111 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 0a d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 58 20 f4 11 40 00 02:04:25.891 READ FPDMA QUEUED 60 20 50 da 44 67 40 00 02:04:25.891 READ FPDMA QUEUED 60 10 48 f8 e8 01 40 00 02:04:25.891 READ FPDMA QUEUED 61 08 68 00 10 fb 40 00 02:04:25.891 WRITE FPDMA QUEUED 60 08 40 40 59 f5 40 00 02:04:25.891 READ FPDMA QUEUED Error 110 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 6a d0 b1 c4 66 Error: WP at LBA = 0x06c4b1d0 = 113553872 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 08 70 e0 ef db 40 00 02:03:24.996 WRITE FPDMA QUEUED 60 08 68 d0 b1 c4 40 00 02:03:24.996 READ FPDMA QUEUED 61 08 68 60 13 d9 40 00 02:03:24.996 WRITE FPDMA QUEUED 60 08 60 20 66 bc 40 00 02:03:24.996 READ FPDMA QUEUED 61 08 60 e8 81 67 40 00 02:03:24.995 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.