smartctl 7.2 2020-12-30 r5155 [FreeBSD 13.0-RELEASE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA MK7559GSXF Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: GQ006B User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Mar 9 17:31:25 2022 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 198) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 2118 4 Start_Stop_Count -O--CK 100 100 000 - 5176 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 2840 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 013 013 000 - 34814 10 Spin_Retry_Count PO--CK 203 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 4507 191 G-Sense_Error_Rate -O--CK 100 100 000 - 62 192 Power-Off_Retract_Count -O--CK 099 099 000 - 616 193 Load_Cycle_Count -O--CK 082 082 000 - 189516 194 Temperature_Celsius -O---K 100 100 000 - 38 (Min/Max 3/57) 196 Reallocated_Event_Count -O--CK 100 100 000 - 172 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 220 Disk_Shift -O---- 100 100 000 - 48 222 Loaded_Hours -O--CK 016 016 000 - 33891 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 295 240 Head_Flying_Hours P----- 100 100 001 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 236 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 13 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [12] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 5a 00 00 3a 01 5d a0 6a 00 Error: WP at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 40 00 70 00 00 4a c3 6e a8 40 00 00:06:56.674 WRITE FPDMA QUEUED 61 00 10 00 68 00 00 41 b5 cc 20 40 00 00:06:56.674 WRITE FPDMA QUEUED 61 00 10 00 60 00 00 41 b5 2e 68 40 00 00:06:56.674 WRITE FPDMA QUEUED 60 00 08 00 58 00 00 3a 01 5d a0 40 00 00:06:55.260 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:55.260 FLUSH CACHE EXT Error 12 [11] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 42 00 00 3a 01 5d a0 6a 00 Error: UNC at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 3a 01 5d a0 40 00 00:06:51.325 READ FPDMA QUEUED 61 00 08 00 38 00 00 4a c3 6e a0 40 00 00:06:51.324 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:51.324 FLUSH CACHE EXT ef 00 10 00 02 54 66 ef 00 00 00 a0 00 00:06:51.324 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:51.324 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 11 [10] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 0a 00 00 3a 01 5d a0 6a 00 Error: WP at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 38 00 20 00 00 4a c3 6e 68 40 00 00:06:49.266 WRITE FPDMA QUEUED 61 00 10 00 18 00 00 41 b4 f1 98 40 00 00:06:49.266 WRITE FPDMA QUEUED 61 00 10 00 10 00 00 41 b5 2e 60 40 00 00:06:49.266 WRITE FPDMA QUEUED 60 00 08 00 08 00 00 3a 01 5d a0 40 00 00:06:47.405 READ FPDMA QUEUED 61 00 08 00 00 00 00 41 b4 54 08 40 00 00:06:47.381 WRITE FPDMA QUEUED Error 10 [9] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 f2 00 00 3a 01 5d a0 6a 00 Error: UNC at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 3a 01 5d a0 40 00 00:06:43.447 READ FPDMA QUEUED 61 00 08 00 e8 00 00 46 d7 60 10 40 00 00:06:43.447 WRITE FPDMA QUEUED 61 00 18 00 e0 00 00 46 d7 50 08 40 00 00:06:43.447 WRITE FPDMA QUEUED 61 00 08 00 d8 00 00 4b c3 30 d0 40 00 00:06:43.447 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:43.418 FLUSH CACHE EXT Error 9 [8] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 82 00 00 3a 01 5d a0 6a 00 Error: WP at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 40 00 a0 00 00 4a c3 6e 20 40 00 00:06:41.234 WRITE FPDMA QUEUED 61 00 20 00 98 00 00 41 b5 2e 48 40 00 00:06:41.234 WRITE FPDMA QUEUED 61 00 18 00 90 00 00 41 b5 cc 10 40 00 00:06:41.234 WRITE FPDMA QUEUED 61 00 18 00 88 00 00 41 b4 f1 88 40 00 00:06:41.234 WRITE FPDMA QUEUED 60 00 08 00 80 00 00 3a 01 5d a0 40 00 00:06:39.468 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 6a 00 00 3a 01 5d a0 6a 00 Error: UNC at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 68 00 00 3a 01 5d a0 40 00 00:06:35.544 READ FPDMA QUEUED 61 00 08 00 60 00 00 4a c3 6e 18 40 00 00:06:35.544 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:06:35.422 FLUSH CACHE EXT 61 00 10 00 50 00 00 41 b4 f1 80 40 00 00:06:35.422 WRITE FPDMA QUEUED 61 00 30 00 48 00 00 4a c3 6d e8 40 00 00:06:35.422 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 c2 00 00 3a 01 5d a0 6a 00 Error: UNC at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 c0 00 00 3a 01 5d a0 40 00 00:06:31.493 READ FPDMA QUEUED 61 00 90 00 b8 00 00 37 cb a5 00 40 00 00:06:31.493 WRITE FPDMA QUEUED ef 00 10 00 02 54 66 ef 00 00 00 a0 00 00:06:31.493 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:31.492 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 00:06:31.492 IDENTIFY DEVICE Error 6 [5] occurred at disk power-on lifetime: 10860 hours (452 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 b2 00 00 3a 01 5d a0 6a 00 Error: UNC at LBA = 0x3a015da0 = 973168032 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 3a 01 5d a0 40 00 00:06:27.569 READ FPDMA QUEUED 61 00 08 00 a8 00 00 37 be 84 d8 40 00 00:06:27.569 WRITE FPDMA QUEUED ef 00 10 00 02 54 66 ef 00 00 00 a0 00 00:06:27.569 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:06:27.569 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 45 00 00 00 00 00 00 00 a0 00 00:06:27.568 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 34072 - # 2 Short offline Interrupted (host reset) 80% 5863 - # 3 Short offline Completed without error 00% 1952 - # 4 Short offline Completed without error 00% 1935 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 11/38 Celsius Lifetime Min/Max Temperature: 3/57 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (116) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 12 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC