smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.3-STABLE amd64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD10JFCX-68N6GN0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 82.00A82 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jan 20 14:03:14 2023 +07 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17640) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 198) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 184 183 021 - 1775 4 Start_Stop_Count -O--CK 100 100 000 - 38 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 076 076 000 - 17896 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 38 192 Power-Off_Retract_Count -O--CK 200 200 000 - 24 193 Load_Cycle_Count -O--CK 200 200 000 - 760 194 Temperature_Celsius -O---K 091 084 000 - 56 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 11751 hours (489 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:14.331 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:14.331 SMART READ LOG ec 00 00 00 01 00 00 00 00 00 00 40 08 33d+23:14:14.327 IDENTIFY DEVICE b0 00 d6 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:09.324 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:09.324 SMART READ LOG Error 11 [10] occurred at disk power-on lifetime: 11751 hours (489 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:09.324 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:09.324 SMART READ LOG ec 00 00 00 01 00 00 00 00 00 00 40 08 33d+23:14:09.319 IDENTIFY DEVICE b0 00 d5 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:04.425 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 08 33d+23:14:04.425 SMART WRITE LOG Error 10 [9] occurred at disk power-on lifetime: 11751 hours (489 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 08 33d+23:13:54.894 SMART WRITE LOG b0 00 d5 00 01 00 00 00 c2 4f e0 40 08 33d+23:13:54.894 SMART READ LOG ec 00 00 00 01 00 00 00 00 00 00 40 08 33d+23:13:54.891 IDENTIFY DEVICE b0 00 d5 00 01 00 00 00 c2 4f e0 40 08 33d+23:13:40.046 SMART READ LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 08 33d+23:13:40.046 SMART WRITE LOG Error 9 [8] occurred at disk power-on lifetime: 6044 hours (251 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 40 00 29d+20:29:59.332 SET FEATURES [Set transfer mode] ef 00 03 00 46 00 00 00 00 00 00 40 00 29d+20:29:59.297 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 40 00 29d+20:29:59.297 IDENTIFY DEVICE ef 00 03 00 0c 00 00 00 00 00 00 00 00 29d+20:29:40.193 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 00 00 29d+20:29:40.192 IDENTIFY DEVICE Error 8 [7] occurred at disk power-on lifetime: 6044 hours (251 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 40 00 29d+20:29:59.297 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 40 00 29d+20:29:59.297 IDENTIFY DEVICE ef 00 03 00 0c 00 00 00 00 00 00 00 00 29d+20:29:40.193 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 00 00 29d+20:29:40.192 IDENTIFY DEVICE ea 00 00 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.376 FLUSH CACHE EXT Error 7 [6] occurred at disk power-on lifetime: 6044 hours (251 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 0c 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 0c 00 00 00 00 00 00 00 00 29d+20:29:40.193 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 00 00 29d+20:29:40.192 IDENTIFY DEVICE ea 00 00 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.376 FLUSH CACHE EXT ef 00 02 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.342 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.308 SET FEATURES [Enable read look-ahead] Error 6 [5] occurred at disk power-on lifetime: 5974 hours (248 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 40 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.376 FLUSH CACHE EXT ef 00 02 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.342 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.308 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 40 00 26d+23:23:10.261 SET FEATURES [Set transfer mode] ef 00 03 00 46 00 00 00 00 00 00 40 00 26d+23:23:10.225 SET FEATURES [Set transfer mode] Error 5 [4] occurred at disk power-on lifetime: 5974 hours (248 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.342 SET FEATURES [Enable write cache] ef 00 aa 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.308 SET FEATURES [Enable read look-ahead] ef 00 03 00 46 00 00 00 00 00 00 40 00 26d+23:23:10.261 SET FEATURES [Set transfer mode] ef 00 03 00 46 00 00 00 00 00 00 40 00 26d+23:23:10.225 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 40 00 26d+23:23:10.180 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 17883 - # 2 Short offline Completed without error 00% 17859 - # 3 Short offline Completed without error 00% 17835 - # 4 Short offline Completed without error 00% 17811 - # 5 Short offline Completed without error 00% 17787 - # 6 Short offline Completed without error 00% 17763 - # 7 Extended offline Completed without error 00% 17747 - # 8 Short offline Completed without error 00% 17739 - # 9 Short offline Completed without error 00% 17715 - #10 Short offline Completed without error 00% 17691 - #11 Short offline Completed without error 00% 17667 - #12 Short offline Completed without error 00% 17643 - #13 Short offline Completed without error 00% 17619 - #14 Short offline Completed without error 00% 17595 - #15 Extended offline Completed without error 00% 17579 - #16 Short offline Completed without error 00% 17571 - #17 Short offline Completed without error 00% 17547 - #18 Short offline Completed without error 00% 17523 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 56 Celsius Power Cycle Min/Max Temperature: 45/63 Celsius Lifetime Min/Max Temperature: 24/63 Celsius Under/Over Temperature Limit Count: 0/319 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (99) SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 1 R_ERR response for data FIS 0x0003 2 1 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 3 R_ERR response for non-data FIS 0x0006 2 3 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 1 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 20009407 Vendor specific