smartctl 7.2 2021-09-14 r5236 [FreeBSD 13.0-STABLE amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K02 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Nov 21 00:59:26 2021 +03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 287) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 199 051 - 0 3 Spin_Up_Time POS--K 169 169 021 - 6525 4 Start_Stop_Count -O--CK 100 100 000 - 7 5 Reallocated_Sector_Ct PO--CK 194 194 140 - 199 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 007 007 000 - 68264 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 7 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 3 193 Load_Cycle_Count -O--CK 200 200 000 - 54 194 Temperature_Celsius -O---K 103 096 000 - 47 196 Reallocated_Event_Count -O--CK 194 194 000 - 6 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 30 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 30 [5] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 e1 36 5d 40 00 Error: WP at LBA = 0xe7e1365d = 3890296413 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 70 00 00 88 25 4e 2a 40 08 18d+06:39:34.205 WRITE FPDMA QUEUED 61 00 50 00 68 00 00 88 25 4c 6a 40 08 18d+06:39:34.193 WRITE FPDMA QUEUED 60 01 00 00 60 00 00 e7 e1 35 fa 40 08 18d+06:39:34.193 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:39:34.192 READ LOG EXT 61 00 50 00 48 00 00 88 25 4c 6a 40 08 18d+06:39:32.007 WRITE FPDMA QUEUED Error 29 [4] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 e1 36 5d 40 00 Error: WP at LBA = 0xe7e1365d = 3890296413 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 50 00 48 00 00 88 25 4c 6a 40 08 18d+06:39:32.007 WRITE FPDMA QUEUED 61 00 20 00 40 00 00 88 24 d4 6a 40 08 18d+06:39:32.002 WRITE FPDMA QUEUED 61 00 10 00 38 00 00 88 24 d4 32 40 08 18d+06:39:32.002 WRITE FPDMA QUEUED 61 00 10 00 30 00 00 88 24 8e c2 40 08 18d+06:39:32.002 WRITE FPDMA QUEUED 61 00 30 00 28 00 00 88 24 8c 52 40 08 18d+06:39:32.002 WRITE FPDMA QUEUED Error 28 [3] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 e1 36 5d 40 00 Error: WP at LBA = 0xe7e1365d = 3890296413 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 30 00 f8 00 00 7c 93 8b 2a 40 08 18d+06:39:29.742 WRITE FPDMA QUEUED 61 00 20 00 f0 00 00 7c 93 8a 3a 40 08 18d+06:39:29.738 WRITE FPDMA QUEUED 61 00 10 00 e8 00 00 7c 93 8a 22 40 08 18d+06:39:29.738 WRITE FPDMA QUEUED 61 00 20 00 e0 00 00 7c 93 89 ca 40 08 18d+06:39:29.737 WRITE FPDMA QUEUED 61 00 08 00 d8 00 00 7c 93 87 ea 40 08 18d+06:39:29.737 WRITE FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 e1 36 5d 40 00 Error: WP at LBA = 0xe7e1365d = 3890296413 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 38 00 00 7a 1c 7c aa 40 08 18d+06:39:27.685 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 7a 1c 7b fa 40 08 18d+06:39:27.685 WRITE FPDMA QUEUED 61 00 08 00 28 00 00 7a 1c 7b da 40 08 18d+06:39:27.685 WRITE FPDMA QUEUED 61 00 08 00 20 00 00 7a 1c 7b a2 40 08 18d+06:39:27.685 WRITE FPDMA QUEUED 61 00 08 00 18 00 00 7a 1c 7a aa 40 08 18d+06:39:27.685 WRITE FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 e1 36 5d 40 00 Error: UNC at LBA = 0xe7e1365d = 3890296413 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 d0 00 00 e7 e1 35 fa 40 08 18d+06:39:25.640 READ FPDMA QUEUED 60 00 08 00 c8 00 00 7b 20 d8 52 40 08 18d+06:39:25.640 READ FPDMA QUEUED 60 01 00 00 c0 00 00 8f 9e 96 52 40 08 18d+06:39:25.639 READ FPDMA QUEUED 60 00 58 00 b8 00 00 8e 9a 34 8a 40 08 18d+06:39:25.639 READ FPDMA QUEUED 60 00 08 00 b0 00 00 7b 20 d8 52 40 08 18d+06:39:25.638 READ FPDMA QUEUED Error 25 [0] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 fe d6 f9 40 00 Error: UNC at LBA = 0xe7fed6f9 = 3892238073 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 50 00 00 e7 fe d6 02 40 08 18d+06:33:26.278 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:33:26.278 READ LOG EXT 60 01 00 00 40 00 00 e7 fe d6 02 40 08 18d+06:33:24.405 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:33:24.405 READ LOG EXT 60 01 00 00 30 00 00 e7 fe d6 02 40 08 18d+06:33:22.532 READ FPDMA QUEUED Error 24 [23] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 fe d6 f9 40 00 Error: UNC at LBA = 0xe7fed6f9 = 3892238073 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 40 00 00 e7 fe d6 02 40 08 18d+06:33:24.405 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:33:24.405 READ LOG EXT 60 01 00 00 30 00 00 e7 fe d6 02 40 08 18d+06:33:22.532 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:33:22.531 READ LOG EXT 60 01 00 00 20 00 00 e7 fe d6 02 40 08 18d+06:33:20.659 READ FPDMA QUEUED Error 23 [22] occurred at disk power-on lifetime: 2061 hours (85 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 e7 fe d6 f9 40 00 Error: UNC at LBA = 0xe7fed6f9 = 3892238073 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 30 00 00 e7 fe d6 02 40 08 18d+06:33:22.532 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:33:22.531 READ LOG EXT 60 01 00 00 20 00 00 e7 fe d6 02 40 08 18d+06:33:20.659 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 08 18d+06:33:20.658 READ LOG EXT 60 01 00 00 10 00 00 e7 fe d6 02 40 08 18d+06:33:18.808 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 4 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 47 Celsius Power Cycle Min/Max Temperature: 43/54 Celsius Lifetime Min/Max Temperature: 23/54 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (220) SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 33 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 34 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 8275465 Vendor specific