smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p3 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed May 26 10:57:37 2021 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25500) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 278) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 169 169 021 - 6525 4 Start_Stop_Count -O--CK 100 100 000 - 11 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 060 060 000 - 29866 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 0 193 Load_Cycle_Count -O--CK 200 200 000 - 10 194 Temperature_Celsius -O---K 119 115 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 7 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 [6] occurred at disk power-on lifetime: 6218 hours (259 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 4d 2c 40 00 Error: UNC at LBA = 0x021e4d2c = 35540268 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 08 00 00 02 1e 4a 00 40 08 39d+23:42:16.646 READ FPDMA QUEUED 61 00 01 00 00 00 00 02 10 18 08 40 08 39d+23:42:16.646 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 39d+23:42:16.630 FLUSH CACHE EXT 60 04 00 00 e0 00 00 02 1e 46 00 40 08 39d+23:42:16.461 READ FPDMA QUEUED 60 04 00 00 d8 00 00 02 1e 42 00 40 08 39d+23:42:16.434 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 5908 hours (246 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 62 06 40 00 Error: UNC at LBA = 0x021e6206 = 35545606 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 d8 00 00 02 1e 61 00 40 08 27d+01:46:21.813 READ FPDMA QUEUED 60 04 00 00 d0 00 00 02 1e 5d 00 40 08 27d+01:46:21.810 READ FPDMA QUEUED 60 04 00 00 c8 00 00 02 1e 59 00 40 08 27d+01:46:21.807 READ FPDMA QUEUED 60 04 00 00 c0 00 00 02 1e 55 00 40 08 27d+01:46:21.795 READ FPDMA QUEUED 60 04 00 00 b8 00 00 02 1e 51 00 40 08 27d+01:46:21.792 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 5908 hours (246 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 03 9b 40 00 Error: UNC at LBA = 0x021e039b = 35521435 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 d0 00 00 02 1e 03 00 40 08 27d+01:46:17.102 READ FPDMA QUEUED 60 04 00 00 c8 00 00 02 1d ff 00 40 08 27d+01:46:17.092 READ FPDMA QUEUED 60 04 00 00 c0 00 00 02 1d fb 00 40 08 27d+01:46:17.087 READ FPDMA QUEUED 60 04 00 00 b8 00 00 02 1d f7 00 40 08 27d+01:46:17.068 READ FPDMA QUEUED 61 00 08 00 b0 00 00 8f 18 1d b8 40 08 27d+01:46:17.068 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 6088 hours (253 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 37 bd 40 00 Error: UNC at LBA = 0x021e37bd = 35534781 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 30 00 00 02 1e 37 00 40 08 34d+12:59:02.840 READ FPDMA QUEUED 60 04 00 00 28 00 00 02 1e 33 00 40 08 34d+12:59:02.837 READ FPDMA QUEUED 60 04 00 00 20 00 00 02 1e 2f 00 40 08 34d+12:59:02.834 READ FPDMA QUEUED 60 04 00 00 18 00 00 02 1e 2b 00 40 08 34d+12:59:02.827 READ FPDMA QUEUED 60 04 00 00 10 00 00 02 1e 27 00 40 08 34d+12:59:02.826 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 6537 hours (272 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 57 98 40 00 Error: UNC at LBA = 0x021e5798 = 35542936 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 f0 00 00 02 1e 56 80 40 08 3d+13:41:59.260 READ FPDMA QUEUED 60 04 00 00 e8 00 00 02 1e 52 80 40 08 3d+13:41:59.247 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 3d+13:41:59.240 FLUSH CACHE EXT 60 04 00 00 d0 00 00 02 1e 4e 80 40 08 3d+13:41:59.239 READ FPDMA QUEUED 61 00 08 00 c8 00 00 75 5b 82 a0 40 08 3d+13:41:59.239 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 6537 hours (272 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 2d 53 40 00 Error: UNC at LBA = 0x021e2d53 = 35532115 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 58 00 00 02 1e 2b 00 40 08 3d+13:41:54.952 READ FPDMA QUEUED 61 00 08 00 50 00 00 19 bf 9f 08 40 08 3d+13:41:54.952 WRITE FPDMA QUEUED 60 04 00 00 48 00 00 02 1e 27 00 40 08 3d+13:41:54.951 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 3d+13:41:54.949 FLUSH CACHE EXT 60 04 00 00 30 00 00 02 1e 23 00 40 08 3d+13:41:54.948 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 6268 hours (261 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 1e 4d 2c 40 00 Error: UNC at LBA = 0x021e4d2c = 35540268 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 00 00 b0 00 00 02 1e 4b 00 40 08 42d+01:11:41.452 READ FPDMA QUEUED 60 04 00 00 a8 00 00 02 1e 47 00 40 08 42d+01:11:41.449 READ FPDMA QUEUED 60 04 00 00 a0 00 00 02 1e 43 00 40 08 42d+01:11:41.446 READ FPDMA QUEUED 60 04 00 00 98 00 00 02 1e 3f 00 40 08 42d+01:11:41.439 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 42d+01:11:41.427 FLUSH CACHE EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 13701 - # 2 Extended offline Completed without error 00% 13684 - # 3 Extended offline Completed without error 00% 11405 - # 4 Extended offline Completed without error 00% 11388 - # 5 Extended offline Completed without error 00% 11261 - # 6 Extended offline Completed without error 00% 11244 - # 7 Extended offline Completed without error 00% 1037 - # 8 Extended offline Completed without error 00% 961 - # 9 Short offline Completed without error 00% 882 - #10 Short offline Completed without error 00% 858 - #11 Short offline Completed without error 00% 835 - #12 Short offline Completed without error 00% 811 - #13 Short offline Completed without error 00% 787 - #14 Short offline Completed without error 00% 763 - #15 Short offline Completed without error 00% 739 - #16 Short offline Completed without error 00% 715 - #17 Short offline Completed without error 00% 691 - #18 Short offline Completed without error 00% 667 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 24/35 Celsius Lifetime Min/Max Temperature: 22/37 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (53) SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 137 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 138 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 58165527 Vendor specific