smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p5 amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE4-GP Device Model: WDC WD2002FYPS-01U1B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 04.05G04 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Nov 9 11:01:49 2024 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (41580) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 473) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 37 3 Spin_Up_Time POS--K 162 138 021 - 8883 4 Start_Stop_Count -O--CK 094 094 000 - 6375 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 055 055 000 - 33149 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 999 192 Power-Off_Retract_Count -O--CK 200 200 000 - 168 193 Load_Cycle_Count -O--CK 142 142 000 - 176108 194 Temperature_Celsius -O---K 116 090 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 199 192 000 - 254 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 19036 hours (793 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 4a 3a 00 a2 3c 40 00 Error: UNC at LBA = 0x4a3a00a23c = 318800699964 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 4a a2 39 c0 40 00 00:16:33.061 READ FPDMA QUEUED 61 00 80 00 08 00 00 3a 91 97 80 40 00 00:16:33.060 WRITE FPDMA QUEUED 61 01 00 00 00 00 00 3a 91 96 80 40 00 00:16:33.060 WRITE FPDMA QUEUED 60 00 80 00 08 00 00 4a b2 56 00 40 00 00:16:33.055 READ FPDMA QUEUED 60 01 00 00 00 00 00 4a b2 55 00 40 00 00:16:33.055 READ FPDMA QUEUED Error 11 [10] occurred at disk power-on lifetime: 19036 hours (793 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 4a 39 00 a2 c3 40 00 Error: UNC at LBA = 0x4a3900a2c3 = 318783922883 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 00 00 00 4a a2 39 c0 40 00 00:12:41.598 READ FPDMA QUEUED 61 00 c0 00 00 00 00 25 b7 46 00 40 00 00:12:41.598 WRITE FPDMA QUEUED 60 00 c0 00 00 00 00 3e c6 a4 40 40 00 00:12:41.582 READ FPDMA QUEUED 61 00 40 00 00 00 00 25 b7 45 c0 40 00 00:12:41.581 WRITE FPDMA QUEUED 61 00 40 00 08 00 00 21 95 5f 40 40 00 00:12:41.581 WRITE FPDMA QUEUED Error 10 [9] occurred at disk power-on lifetime: 9692 hours (403 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 04 00 a3 8e 00 e3 24 a3 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 4d+13:15:23.955 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 4d+13:15:23.955 WRITE FPDMA QUEUED ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 4d+13:15:23.955 FLUSH CACHE EXT ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 4d+13:15:09.183 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 4d+13:15:09.183 WRITE FPDMA QUEUED Error 9 [8] occurred at disk power-on lifetime: 9668 hours (402 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 04 00 a3 8e 00 e3 24 a3 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 3d+13:16:53.816 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 3d+13:16:53.816 WRITE FPDMA QUEUED ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 3d+13:16:53.816 FLUSH CACHE EXT ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 3d+13:16:29.717 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 3d+13:16:29.717 WRITE FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 9654 hours (402 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 04 00 a3 8e 00 e3 24 a3 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 2d+23:18:27.107 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 2d+23:18:27.107 WRITE FPDMA QUEUED ea 00 08 00 04 00 00 00 4b fc bf e0 08 2d+23:18:27.106 FLUSH CACHE EXT ea 00 08 00 04 00 00 00 4b fc bf e0 08 2d+23:18:12.355 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 4b fc bf 40 08 2d+23:18:12.355 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 9601 hours (400 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 04 00 a3 8e 00 e3 24 a3 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 18:21:05.842 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 18:21:05.842 WRITE FPDMA QUEUED ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 18:21:05.842 FLUSH CACHE EXT ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 18:20:51.067 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 18:20:51.067 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 9596 hours (399 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 04 00 a3 8e 00 e3 24 a3 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 13:21:07.197 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 13:21:07.196 WRITE FPDMA QUEUED ea 00 08 00 04 00 00 00 4b fc bf e0 08 13:21:07.196 FLUSH CACHE EXT ea 00 08 00 04 00 00 00 4b fc bf e0 08 13:20:52.460 FLUSH CACHE EXT 61 00 08 00 00 00 00 00 4b fc bf 40 08 13:20:52.460 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 8673 hours (361 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 04 00 a3 8e 00 e3 24 a3 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 26d+07:45:10.306 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 26d+07:45:10.306 WRITE FPDMA QUEUED ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 26d+07:45:10.303 FLUSH CACHE EXT ea 00 02 00 04 00 00 00 5f d8 c7 e0 08 26d+07:08:05.747 FLUSH CACHE EXT 61 00 02 00 00 00 00 00 5f d8 c7 40 08 26d+07:08:05.747 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 32395 - # 2 Extended offline Completed without error 00% 23030 - # 3 Short offline Completed without error 00% 22385 - # 4 Short offline Completed without error 00% 16280 - # 5 Extended offline Completed without error 00% 16071 - # 6 Extended offline Completed without error 00% 15903 - # 7 Extended offline Completed without error 00% 15736 - # 8 Extended offline Completed without error 00% 15568 - # 9 Extended offline Completed without error 00% 15399 - #10 Extended offline Completed without error 00% 15231 - #11 Extended offline Completed without error 00% 15064 - #12 Extended offline Completed without error 00% 14896 - #13 Short offline Completed without error 00% 14587 - #14 Short offline Completed without error 00% 10009 - #15 Extended offline Completed without error 00% 7824 - #16 Short offline Completed without error 00% 6995 - #17 Extended offline Completed without error 00% 6832 - #18 Short offline Completed without error 00% 6589 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 22/36 Celsius Lifetime Min/Max Temperature: 22/62 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (190) SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 5484 Vendor specific