smartctl 7.2 2021-09-14 r5236 [FreeBSD 13.0-RELEASE-p4 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-00ERMA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 15.01H15 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Dec 2 19:34:25 2021 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8160) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 83) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 144 142 021 - 3758 4 Start_Stop_Count -O--CK 099 099 000 - 1194 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 055 055 000 - 33425 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 939 192 Power-Off_Retract_Count -O--CK 200 200 000 - 515 193 Load_Cycle_Count -O--CK 200 200 000 - 681 194 Temperature_Celsius -O---K 107 091 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 2 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 3 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 28 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 28 [3] occurred at disk power-on lifetime: 31009 hours (1292 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 9d a5 10 40 00 Error: UNC at LBA = 0x199da510 = 429761808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 78 00 00 19 9d a5 00 40 08 00:35:20.121 READ FPDMA QUEUED 60 01 00 00 50 00 00 2a d2 f5 98 40 08 00:35:20.108 READ FPDMA QUEUED 60 00 08 00 70 00 00 19 14 40 68 40 08 00:35:20.106 READ FPDMA QUEUED 60 01 00 00 48 00 00 2a d2 f4 98 40 08 00:35:20.097 READ FPDMA QUEUED 60 00 08 00 68 00 00 29 25 e6 78 40 08 00:35:20.088 READ FPDMA QUEUED Error 27 [2] occurred at disk power-on lifetime: 31009 hours (1292 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 9d a5 10 40 00 Error: UNC at LBA = 0x199da510 = 429761808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 19 9d a5 10 40 08 00:06:44.728 READ FPDMA QUEUED 60 00 10 00 38 00 00 19 a8 30 18 40 08 00:06:44.728 READ FPDMA QUEUED 60 00 08 00 30 00 00 19 a8 30 28 40 08 00:06:44.723 READ FPDMA QUEUED 60 00 18 00 28 00 00 19 97 ee 80 40 08 00:06:44.722 READ FPDMA QUEUED 60 00 08 00 20 00 00 19 97 ee 98 40 08 00:06:44.714 READ FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 31009 hours (1292 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 29 c4 67 2d 40 00 Error: UNC at LBA = 0x29c4672d = 700737325 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 08 00 90 00 00 21 50 12 00 40 08 00:05:49.514 READ FPDMA QUEUED 60 00 08 00 88 00 00 1a 54 cc 20 40 08 00:05:49.501 READ FPDMA QUEUED 60 01 08 00 78 00 00 21 90 13 00 40 08 00:05:49.488 READ FPDMA QUEUED 60 01 00 00 40 00 00 29 c4 66 d8 40 08 00:05:49.488 READ FPDMA QUEUED 60 01 00 00 38 00 00 29 c4 65 d8 40 08 00:05:49.487 READ FPDMA QUEUED Error 25 [0] occurred at disk power-on lifetime: 31009 hours (1292 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 9d a5 10 40 00 Error: UNC at LBA = 0x199da510 = 429761808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 30 00 00 19 9c c9 c8 40 08 02:40:38.528 READ FPDMA QUEUED 60 00 08 00 b0 00 00 19 9d a5 10 40 08 02:40:38.510 READ FPDMA QUEUED 60 00 18 00 a0 00 00 19 95 d1 60 40 08 02:40:38.510 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 02:40:38.510 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 02:40:38.510 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 24 [23] occurred at disk power-on lifetime: 31009 hours (1292 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 9d a5 10 40 00 Error: UNC at LBA = 0x199da510 = 429761808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 28 00 00 19 95 d1 60 40 08 02:40:36.590 READ FPDMA QUEUED 60 00 58 00 20 00 00 19 a0 ec 78 40 08 02:40:36.588 READ FPDMA QUEUED 60 00 08 00 18 00 00 19 9d a5 10 40 08 02:40:36.581 READ FPDMA QUEUED 60 00 20 00 10 00 00 19 a0 ec 58 40 08 02:40:36.570 READ FPDMA QUEUED 60 00 10 00 08 00 00 19 a8 30 18 40 08 02:40:36.556 READ FPDMA QUEUED Error 23 [22] occurred at disk power-on lifetime: 31009 hours (1292 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 29 c4 67 2d 40 00 Error: UNC at LBA = 0x29c4672d = 700737325 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 b8 00 00 29 ad 24 00 40 08 02:39:33.935 READ FPDMA QUEUED 60 00 c0 00 e8 00 00 24 d9 ec e0 40 08 02:39:33.928 READ FPDMA QUEUED 60 00 80 00 88 00 00 29 ad 10 60 40 08 02:39:33.915 READ FPDMA QUEUED 60 00 40 00 78 00 00 29 ad 10 20 40 08 02:39:33.915 READ FPDMA QUEUED 60 01 00 00 70 00 00 29 c4 66 d8 40 08 02:39:33.915 READ FPDMA QUEUED Error 22 [21] occurred at disk power-on lifetime: 31008 hours (1292 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 9d a5 10 40 00 Error: UNC at LBA = 0x199da510 = 429761808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 90 00 00 19 9d a5 00 40 08 02:22:04.332 READ FPDMA QUEUED 60 00 08 00 88 00 00 19 14 40 68 40 08 02:22:04.320 READ FPDMA QUEUED 60 00 08 00 80 00 00 26 54 86 60 40 08 02:22:04.308 READ FPDMA QUEUED 60 00 08 00 78 00 00 26 14 a8 b0 40 08 02:22:04.297 READ FPDMA QUEUED 60 00 08 00 70 00 00 29 25 e6 78 40 08 02:22:04.281 READ FPDMA QUEUED Error 21 [20] occurred at disk power-on lifetime: 31008 hours (1292 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 19 9d a5 10 40 00 Error: UNC at LBA = 0x199da510 = 429761808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 18 00 18 00 00 19 9d a5 00 40 08 01:55:08.889 READ FPDMA QUEUED 60 00 08 00 10 00 00 19 14 40 68 40 08 01:55:08.878 READ FPDMA QUEUED 60 00 08 00 08 00 00 26 54 86 60 40 08 01:55:08.866 READ FPDMA QUEUED 60 00 08 00 00 00 00 26 14 a8 b0 40 08 01:55:08.855 READ FPDMA QUEUED 60 00 08 00 f0 00 00 29 25 e6 78 40 08 01:55:08.839 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 25/36 Celsius Lifetime Min/Max Temperature: 0/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (318) SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 1591 Vendor specific