smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital AV-GP Device Model: WDC WD5000AVVS-00ZWB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01B01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Mar 16 12:51:42 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 194 051 - 4 3 Spin_Up_Time PO---- 161 158 021 - 4941 4 Start_Stop_Count -O--CK 084 084 000 - 16055 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 070 070 000 - 22151 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 085 085 000 - 15892 190 Airflow_Temperature_Cel -O---K 060 039 040 Past 40 192 Power-Off_Retract_Count -O--CK 193 193 000 - 5533 193 Load_Cycle_Count -O--CK 195 195 000 - 16055 194 Temperature_Celsius -O---K 107 086 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 198 000 - 0 198 Offline_Uncorrectable ----C- 200 199 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 12 200 Multi_Zone_Error_Rate ---R-- 200 167 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 127 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 127 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 12 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d0 25 10 0f 00 00 00 00 00 00 00 18 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 01 00 00 64 10 83 18 0f 25 00 00 00 00:00:25.874 NOP [Abort queued commands] 18 d7 25 10 03 00 12 00 52 00 00 00 18 00:17:29.742 RECALIBRATE [RET-4] 00 07 00 00 78 10 d7 19 03 25 00 00 00 00:00:16.402 NOP [Abort queued commands] Error 126 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 06 60 02 5a 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 10 02 04 00 5a 2f 00 00 08 00:00:47.312 DEVICE RESET 19 cb 61 02 49 00 d0 08 b8 08 00 00 1e 00:02:29.963 RECALIBRATE [RET-4] 08 c8 10 00 10 02 cb 1e 49 61 00 00 08 00:00:04.304 DEVICE RESET Error 125 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 cb 60 02 49 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 d0 10 00 10 02 cb 1e 49 61 00 00 08 00:00:47.312 DEVICE RESET 1e ca 61 02 49 00 c8 08 10 10 00 00 18 00:02:29.963 RECALIBRATE [RET-4] 08 b8 10 00 10 02 ca 1e 49 60 00 00 08 00:00:04.288 DEVICE RESET Error 124 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d5 60 02 0c 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 10 02 d3 00 0c 2f 00 00 08 00:00:47.280 DEVICE RESET 19 28 2f 01 fc 00 b0 08 b8 08 00 00 00 00:02:10.090 RECALIBRATE [RET-4] 08 b0 08 00 b8 01 16 19 d1 60 00 00 08 00:00:04.097 DEVICE RESET Error 123 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 2a 60 01 fc 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 10 01 28 00 fc 2f 00 00 08 00:00:47.280 DEVICE RESET 19 14 2f 01 d1 00 b0 08 b8 08 00 00 00 00:01:59.062 RECALIBRATE [RET-4] 08 b0 08 00 b8 01 e7 19 be 60 00 00 08 00:00:04.097 DEVICE RESET Error 122 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 16 60 01 d1 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 10 01 14 00 d1 2f 00 00 08 00:00:47.280 DEVICE RESET 19 e5 2f 01 be 00 b0 08 b8 08 00 00 00 00:01:54.407 RECALIBRATE [RET-4] 08 b0 08 00 b8 01 55 19 ae 60 00 00 08 00:00:04.097 DEVICE RESET Error 121 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e7 60 01 be 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 10 01 e5 00 be 2f 00 00 08 00:00:47.280 DEVICE RESET 19 54 60 01 ae 00 b0 08 b8 08 00 00 19 00:01:50.165 RECALIBRATE [RET-4] 08 b0 08 00 c8 01 54 19 ae 60 00 00 08 00:00:51.376 DEVICE RESET Error 120 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 55 60 01 ae 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 b0 08 00 c8 01 54 19 ae 60 00 00 08 00:00:47.280 DEVICE RESET 19 53 60 01 ae 00 b0 08 c8 08 00 00 19 00:01:50.164 RECALIBRATE [RET-4] 08 b0 00 00 68 01 46 19 ae 60 00 00 08 00:00:26.800 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 16523 - # 2 Extended offline Aborted by host 90% 1541 - # 3 Short offline Completed without error 00% 1522 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 23/40 Celsius Lifetime Min/Max Temperature: 23/61 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (30) SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 4329 Vendor specific