This makes binfmt processing behave like tmpfiles processing which
follows the same specification as systemd.
This fixes#48.
X-Gentoo-Bug: 545162
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=545162
It has been determined that it will be best for gentoo's net.* scripts
to be in a separate package to allow independent development.
This package will be called netifrc and maintained by Gentoo.
Certain services were not being enabled by default if PREFIX was set.
This appears to have been intended for Gentoo Prefix systems which are
indicated by MKPREFIX not PREFIX.
Signed-off-by: Andrew Gregory <andrew.gregory.8@gmail.com>
Initially, we were creating tmpfiles entries in the sysinit runlevel and
again in the boot runlevel. Systemd runs the --create and --remove
options in one service called systemd-tmpfiles-setup after the local
file systems are mounted. Now we have a service called tmpfiles.setup
which emulates this.
This also closes the bug mentioned below, since we were originally
writing to files that were on read-only file systems and that were not
available.
Reported-by: <devurandom@gmx.net>
X-Gentoo-Bug: 439012
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=439012
runlevels/Makefile currently uses ${PREFIX} when creating the initial
runlevel symlinks, but the init files are installed to ${INITDIR},
which results in broken symlinks if ${SYSCONFDIR} is set to something
other than ${PREFIX}/etc
Signed-off-by: Andrew Gregory <andrew.gregory.8@gmail.com>
Now that the tmpfiles.d code is more tested, actually call it from
init.d. It assumes that /run is already available when it runs.
Please note it runs TWICE.
- During sysinit, ideally just after /dev/shm is created, but before
udev has started. After udev is also acceptable, but not ideal.
- During boot, ideally just after localmount has completed.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
net.* and module loading require sysfs now, and if udev is not in use,
it is not always loaded early enough, esp for net.lo. Force it to come
up during sysinit instead.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
The OpenRC upstream default network stack was changed, but there was no
reason to change it. Now since we have the MKNET build switch, it is
easy for the gentoo ebuild to install oldnet by default.
The upstream default is newnet.
The MKNET variable can be used to select the network stack you want to
build and install with OpenRC.
The current default is the gentoo "oldnet" stack. If you want to install
the OpenRC newnet stack, use MKNET=newnet on the make command line.
This reverts commit 5994e55937.
There are situations where these scripts can be useful, so I am bringing
them back. Also, I want to start discussions about simplifying the
OpenRC network stack.
Modify the swap script so it starts before and stops after localmount.
Also, on linux, this script should skip mounting swap on loopback.
Add a swapfiles script which runs after localmount and is designed to
activate additional swap space which could not be activated before
localmount was run. This includes loopback swap on linux and swapfiles
which are on local file systems that were not mounted when swap was
activated initially.
The start code does reactivate swap that is already active, but this is
not an error condition.
Reported-by: Giampaolo Tomassoni <giampaolo@tomassoni.biz>
X-Gentoo-Bug: 401003
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=401003
The migrate-run service was hanging when parallel startup was enabled
because of its dependencies. This integrates the logic for this service
into bootmisc, which will avoid the issues with parallel startup.
I would like to thank Robin H. Johnson <robbat2@gentoo.org> for his
input on this patch
These scripts are not supported, and they have several major design
issues such as not being able to stop, start or allow a dependency on a
single interface.
Some variable references were written as $(foo), but the majority were
written as ${foo}. This commit changes all of the variable references
to using braces.
The tree contained many operating system specific Makefiles which were
being included in other Makefiles. This commit removes those and adds
the code to the makefiles which included them using make's conditional
processing.
X-Gentoo-Bug: 387441
X-Gentoo-Bug-URL: http://bugs.gentoo.org/show_bug.cgi?id=387441
This simply assigns static addresses and an optional default route.
It's possible to add external commands as well, so to create a bonded interface.
Hopefully we can add a few examples to satisfy most of the old net.lo, which
is no longer installed into boot by default.
Split halt.sh into halt, killprocs, romount and savecache services.
The reboot runlevel is removed but mapped to shutdown.
The halt script should be moved to the sysvinit package.
mounting various bits in /dev and /sys.
init.sh JUST mounts /lib/rc/init.d (and /proc for Linux systems)
To make development of this easier we now return an empty RC_STRINGLIST
instead of a NULL for empty things.
If you don't have a udev init script installed, don't reboot your box OR
roll back to an older OpenRC version.
Lowercase all configurable variables, non configurations remain uppercase.
Replace rc_env_bool with rc_yesno.
Split localmount info procfs (Linux) and dumpon, savecore (BSD)
