80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/HDD/HPE/MB0500/MB0500GCEHE/068950F69B67
Andrey Ponomarenko 2a811b67c1 Update of reports (new: 6895, modified: 16)
2025-01-05 01:57:11 +03:00

387 lines
21 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.1-RELEASE-p5 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: MB0500GCEHE
Serial Number: --
LU WWN Device Id: 5 0014ee ...
Firmware Version: HPG1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database 7.3/5528
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Oct 16 01:08:33 2024 AEDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Unavailable
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7980) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 81) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 335
3 Spin_Up_Time POS--K 174 171 021 - 2275
4 Start_Stop_Count -O--CK 100 100 000 - 457
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate POSR-K 200 200 051 - 0
9 Power_On_Hours -O--CK 082 082 000 - 13349
10 Spin_Retry_Count PO--CK 100 100 051 - 0
11 Calibration_Retry_Count PO--CK 100 100 051 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 457
180 Unknown_HDD_Attribute POSR-K 200 200 100 - 0
184 End-to-End_Error PO--CK 100 100 097 - 0
187 Reported_Uncorrect -O--CK 100 001 000 - 234
188 Command_Timeout -O--CK 100 094 000 - 13
190 Airflow_Temperature_Cel -O---K 064 059 045 - 36
192 Power-Off_Retract_Count -O--CK 200 200 000 - 100
193 Load_Cycle_Count -O--CK 200 200 000 - 356
194 Temperature_Celsius -O---K 107 102 000 - 36
195 Hardware_ECC_Recovered -OS-CK 200 200 000 - 0
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 23
198 Offline_Uncorrectable ----CK 200 200 000 - 16
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 20
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb5 GPL,SL VS 1 Device vendor specific log
0xb6 GPL VS 1903 Device vendor specific log
0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 24 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 234 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 234 [17] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f5 86 40 00 Error: UNC at LBA = 0x3a13f586 = 974386566
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 a0 00 00 3a 13 f5 80 40 08 15:25:30.105 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:30.101 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:30.101 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:30.101 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:30.100 SET FEATURES [Enable SATA feature]
Error 233 [16] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f5 86 40 00 Error: UNC at LBA = 0x3a13f586 = 974386566
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 30 00 00 3a 13 f5 80 40 08 15:25:28.306 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:28.303 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:28.303 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:28.302 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:28.302 SET FEATURES [Enable SATA feature]
Error 232 [15] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f5 86 40 00 Error: UNC at LBA = 0x3a13f586 = 974386566
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 98 00 00 3a 13 f5 80 40 08 15:25:26.508 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:26.506 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:26.504 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:26.504 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:26.504 SET FEATURES [Enable SATA feature]
Error 231 [14] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f5 86 40 00 Error: UNC at LBA = 0x3a13f586 = 974386566
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 40 00 00 3a 13 f5 80 40 08 15:25:24.717 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:24.716 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:24.714 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:24.714 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:24.714 SET FEATURES [Enable SATA feature]
Error 230 [13] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f5 86 40 00 Error: UNC at LBA = 0x3a13f586 = 974386566
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 28 00 00 3a 13 f5 80 40 08 15:25:22.940 READ FPDMA QUEUED
60 00 08 00 20 00 00 3a 13 f5 78 40 08 15:25:22.940 READ FPDMA QUEUED
60 00 08 00 18 00 00 3a 13 f5 70 40 08 15:25:22.940 READ FPDMA QUEUED
60 00 08 00 10 00 00 3a 13 f5 68 40 08 15:25:22.939 READ FPDMA QUEUED
60 00 08 00 08 00 00 3a 13 f5 60 40 08 15:25:22.939 READ FPDMA QUEUED
Error 229 [12] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f0 fb 40 00 Error: UNC at LBA = 0x3a13f0fb = 974385403
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 18 00 00 3a 13 f0 f8 40 08 15:25:21.090 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:21.087 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:21.087 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:21.087 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:21.085 SET FEATURES [Enable SATA feature]
Error 228 [11] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f0 fb 40 00 Error: UNC at LBA = 0x3a13f0fb = 974385403
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 b8 00 00 3a 13 f0 f8 40 08 15:25:19.291 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:19.288 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:19.288 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:19.288 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:19.287 SET FEATURES [Enable SATA feature]
Error 227 [10] occurred at disk power-on lifetime: 9776 hours (407 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 3a 13 f0 fb 40 00 Error: UNC at LBA = 0x3a13f0fb = 974385403
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 00 00 00 3a 13 f0 f8 40 08 15:25:17.493 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:17.490 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:25:17.489 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:25:17.489 SET FEATURES [Set transfer mode]
ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:25:17.489 SET FEATURES [Enable SATA feature]
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 13211 974000030
# 2 Extended offline Completed: read failure 90% 12324 974000030
# 3 Extended offline Completed: read failure 90% 12323 974000030
# 4 Extended offline Completed: read failure 90% 11716 974000030
# 5 Extended offline Completed: read failure 90% 10478 974000030
# 6 Extended offline Completed: read failure 90% 10006 974000030
# 7 Extended offline Completed: read failure 90% 9932 974000030
# 8 Extended offline Completed: read failure 90% 9932 974000030
# 9 Extended offline Completed: read failure 90% 9932 974000030
#10 Extended offline Completed: read failure 90% 9932 974000030
#11 Extended offline Completed: read failure 90% 9932 974000030
#12 Extended offline Completed: read failure 90% 9932 974000030
#13 Extended offline Completed: read failure 90% 9932 974000030
#14 Extended offline Completed: read failure 90% 9932 974000030
#15 Extended offline Completed: read failure 90% 9736 973219881
#16 Extended offline Completed: read failure 90% 9713 973605476
#17 Extended offline Completed: read failure 90% 9713 974000030
#18 Extended offline Completed: read failure 90% 9713 973605476
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 36 Celsius
Power Cycle Min/Max Temperature: 35/40 Celsius
Lifetime Min/Max Temperature: 0/41 Celsius
Specified Max Operating Temperature: 60 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (182)
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 457 --- Lifetime Power-On Resets
0x01 0x010 4 13349 --- Power-on Hours
0x01 0x018 6 9768577735 --- Logical Sectors Written
0x01 0x020 6 102247492 --- Number of Write Commands
0x01 0x028 6 931560053863 --- Logical Sectors Read
0x01 0x030 6 2344225690 --- Number of Read Commands
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 14000 --- Spindle Motor Power-on Hours
0x03 0x010 4 13997 --- Head Flying Hours
0x03 0x018 4 457 --- Head Load Events
0x03 0x020 4 200 N-- Number of Reallocated Logical Sectors
0x03 0x028 4 1182 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 100 N-- Number of Reported Uncorrectable Errors
0x04 0x010 4 100 N-- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 36 --- Current Temperature
0x05 0x010 1 35 --- Average Short Term Temperature
0x05 0x018 1 28 --- Average Long Term Temperature
0x05 0x020 1 41 --- Highest Temperature
0x05 0x028 1 18 --- Lowest Temperature
0x05 0x030 1 35 --- Highest Average Short Term Temperature
0x05 0x038 1 21 --- Lowest Average Short Term Temperature
0x05 0x040 1 33 --- Highest Average Long Term Temperature
0x05 0x048 1 26 --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 2127 --- Number of Hardware Resets
0x06 0x010 4 9975 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 36 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 18 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 23897 Vendor specific
View Git Blame Copy Permalink