mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
203 lines
10 KiB
Plaintext
203 lines
10 KiB
Plaintext
smartctl 7.3 2022-02-28 r5338 [OpenBSD 7.3 amd64] (local build)
|
|
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Device Model: SAMSUNG HD161HJ
|
|
Serial Number: --
|
|
LU WWN Device Id: 5 0000f0 ...
|
|
Firmware Version: GF100-07
|
|
User Capacity: 160,041,885,696 bytes [160 GB]
|
|
Sector Size: 512 bytes logical/physical
|
|
Device is: Not in smartctl database 7.3/5319
|
|
ATA Version is: ATA8-ACS T13/1699-D revision 3b
|
|
SATA Version is: SATA 2.5, 3.0 Gb/s
|
|
Local Time is: Wed Jun 7 05:44:00 2023 MSK
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART overall-health self-assessment test result: PASSED
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x82) Offline data collection activity
|
|
was completed without error.
|
|
Auto Offline Data Collection: Enabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: ( 2640) seconds.
|
|
Offline data collection
|
|
capabilities: (0x5b) SMART execute Offline immediate.
|
|
Auto Offline data collection on/off support.
|
|
Suspend Offline collection upon new
|
|
command.
|
|
Offline surface scan supported.
|
|
Self-test supported.
|
|
No Conveyance Self-test supported.
|
|
Selective Self-test supported.
|
|
SMART capabilities: (0x0003) Saves SMART data before entering
|
|
power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x01) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 44) minutes.
|
|
SCT capabilities: (0x003f) SCT Status supported.
|
|
SCT Error Recovery Control supported.
|
|
SCT Feature Control supported.
|
|
SCT Data Table supported.
|
|
|
|
SMART Attributes Data Structure revision number: 18
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
|
|
3 Spin_Up_Time 0x0007 073 073 011 Pre-fail Always - 4000
|
|
4 Start_Stop_Count 0x0032 078 078 000 Old_age Always - 21882
|
|
5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 2
|
|
7 Seek_Error_Rate 0x000f 252 252 051 Pre-fail Always - 0
|
|
8 Seek_Time_Performance 0x0025 090 090 015 Pre-fail Offline - 4752
|
|
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 2222628
|
|
10 Spin_Retry_Count 0x0033 252 252 051 Pre-fail Always - 0
|
|
11 Calibration_Retry_Count 0x0012 252 252 000 Old_age Always - 0
|
|
12 Power_Cycle_Count 0x0032 087 087 000 Old_age Always - 12872
|
|
184 End-to-End_Error 0x0032 252 252 000 Old_age Always - 0
|
|
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 92182
|
|
188 Command_Timeout 0x0032 252 252 000 Old_age Always - 0
|
|
190 Airflow_Temperature_Cel 0x0022 124 103 000 Old_age Always - 43
|
|
194 Temperature_Celsius 0x0022 124 103 000 Old_age Always - 43
|
|
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 0
|
|
196 Reallocated_Event_Count 0x0032 099 099 000 Old_age Always - 2
|
|
197 Current_Pending_Sector 0x0012 252 098 000 Old_age Always - 0
|
|
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
|
|
199 UDMA_CRC_Error_Count 0x0036 200 152 000 Old_age Always - 0
|
|
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
|
|
201 Soft_Read_Error_Rate 0x000a 252 252 000 Old_age Always - 0
|
|
|
|
SMART Error Log Version: 1
|
|
Warning: ATA error count 65535 inconsistent with error log pointer 1
|
|
|
|
ATA Error Count: 65535 (device log contains only the most recent five errors)
|
|
CR = Command Register [HEX]
|
|
FR = Features Register [HEX]
|
|
SC = Sector Count Register [HEX]
|
|
SN = Sector Number Register [HEX]
|
|
CL = Cylinder Low Register [HEX]
|
|
CH = Cylinder High Register [HEX]
|
|
DH = Device/Head Register [HEX]
|
|
DC = Device Command Register [HEX]
|
|
ER = Error register [HEX]
|
|
ST = Status register [HEX]
|
|
Powered_Up_Time is measured from power on, and printed as
|
|
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
|
|
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
|
|
|
|
Error 65535 occurred at disk power-on lifetime: 18421 hours (767 days + 13 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 51 01 25 00 00 e0 Error: ABRT
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
ef 02 00 00 00 00 a0 04 00:03:58.000 SET FEATURES [Enable write cache]
|
|
f5 00 00 00 00 00 a0 04 00:03:58.000 SECURITY FREEZE LOCK
|
|
ef 66 00 00 00 00 a0 04 00:03:58.000 SET FEATURES [Disable revert defaults]
|
|
c6 00 10 00 00 00 a0 00 00:03:58.000 SET MULTIPLE MODE
|
|
ef 03 45 00 00 00 a0 04 00:03:58.000 SET FEATURES [Set transfer mode]
|
|
|
|
Error 65534 occurred at disk power-on lifetime: 18421 hours (767 days + 13 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 51 01 25 00 00 e0 Error: ABRT
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
ef 02 00 00 00 00 a0 04 00:00:23.000 SET FEATURES [Enable write cache]
|
|
f5 00 00 00 00 00 a0 04 00:00:23.000 SECURITY FREEZE LOCK
|
|
ef 66 00 00 00 00 a0 04 00:00:23.000 SET FEATURES [Disable revert defaults]
|
|
c6 00 10 00 00 00 a0 00 00:00:23.000 SET MULTIPLE MODE
|
|
ef 03 45 00 00 00 a0 04 00:00:23.000 SET FEATURES [Set transfer mode]
|
|
|
|
Error 65533 occurred at disk power-on lifetime: 18421 hours (767 days + 13 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 51 01 25 00 00 e0 Error: ABRT
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
ef 02 00 00 00 00 a0 04 00:02:46.000 SET FEATURES [Enable write cache]
|
|
ef 66 00 00 00 00 a0 04 00:02:46.000 SET FEATURES [Disable revert defaults]
|
|
c6 00 10 00 00 00 a0 04 00:02:45.000 SET MULTIPLE MODE
|
|
ef 03 45 00 00 00 a0 04 00:02:45.000 SET FEATURES [Set transfer mode]
|
|
ef 03 0c 00 00 00 a0 04 00:02:45.000 SET FEATURES [Set transfer mode]
|
|
|
|
Error 65532 occurred at disk power-on lifetime: 18421 hours (767 days + 13 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 51 01 25 00 00 e0 Error: ABRT
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
ef 02 00 00 00 00 a0 04 00:06:48.000 SET FEATURES [Enable write cache]
|
|
ef 66 00 00 00 00 a0 04 00:06:48.000 SET FEATURES [Disable revert defaults]
|
|
c6 00 10 00 00 00 a0 04 00:06:48.000 SET MULTIPLE MODE
|
|
ef 03 45 00 00 00 a0 04 00:06:48.000 SET FEATURES [Set transfer mode]
|
|
ef 03 0c 00 00 00 a0 04 00:06:48.000 SET FEATURES [Set transfer mode]
|
|
|
|
Error 65531 occurred at disk power-on lifetime: 18416 hours (767 days + 8 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 51 01 25 00 00 e0 Error: ABRT
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
ef 02 00 00 00 00 a0 04 00:00:25.000 SET FEATURES [Enable write cache]
|
|
f5 00 00 00 00 00 a0 04 00:00:25.000 SECURITY FREEZE LOCK
|
|
ef 66 00 00 00 00 a0 04 00:00:25.000 SET FEATURES [Disable revert defaults]
|
|
c6 00 10 00 00 00 a0 00 00:00:25.000 SET MULTIPLE MODE
|
|
ef 03 45 00 00 00 a0 04 00:00:25.000 SET FEATURES [Set transfer mode]
|
|
|
|
Warning! SMART Self-Test Log Structure error: invalid SMART checksum.
|
|
SMART Self-test log structure revision number 0
|
|
Warning: ATA Specification requires self-test log structure revision number = 1
|
|
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
|
|
# 1 Extended offline Completed without error 00% 15905 -
|
|
# 2 Short offline Completed without error 00% 15812 -
|
|
# 3 Short offline Completed without error 00% 15799 -
|
|
# 4 Short offline Completed without error 00% 15777 -
|
|
|
|
SMART Selective self-test log data structure revision number 0
|
|
Note: revision number not 1 implies that no selective self-test has ever been run
|
|
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|
1 0 0 Not_testing
|
|
2 0 0 Not_testing
|
|
3 0 0 Not_testing
|
|
4 0 0 Not_testing
|
|
5 0 0 Not_testing
|
|
Selective self-test flags (0x0):
|
|
After scanning selected spans, do NOT read-scan remainder of disk.
|
|
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|