80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/HDD/Samsung/HD161/HD161HJ/7D09EFE5B704
Andrey Ponomarenko b1c41e7edc Update of reports (new: 3637, modified: 0)
2022-03-18 23:39:11 +03:00

316 lines
16 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD161HJ
Serial Number: --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: GF100-07
User Capacity: 160,040,803,840 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 3b
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Mon Jun 14 20:47:15 2021 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 39) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 2640) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 44) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 18
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 252 100 051 - 0
3 Spin_Up_Time POS--- 073 073 011 - 4000
4 Start_Stop_Count -O--CK 092 092 000 - 8077
5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0
7 Seek_Error_Rate POSR-- 252 252 051 - 0
8 Seek_Time_Performance P-S--K 252 252 015 - 0
9 Power_On_Hours -O--CK 095 095 000 - 2613913
10 Spin_Retry_Count PO--CK 252 252 051 - 0
11 Calibration_Retry_Count -O--C- 099 099 000 - 4
12 Power_Cycle_Count -O--CK 095 095 000 - 4436
184 End-to-End_Error -O--CK 252 252 000 - 0
187 Reported_Uncorrect -O--CK 001 001 000 - 1742
188 Command_Timeout -O--CK 252 252 000 - 0
190 Airflow_Temperature_Cel -O---K 157 085 000 - 32
194 Temperature_Celsius -O---K 157 085 000 - 32
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 0
196 Reallocated_Event_Count -O--CK 252 252 000 - 0
197 Current_Pending_Sector -O--C- 252 099 000 - 0
198 Offline_Uncorrectable ----CK 252 252 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 200 199 000 - 0
200 Multi_Zone_Error_Rate -O-R-- 252 100 000 - 0
201 Soft_Read_Error_Rate -O-R-- 252 252 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 2163 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2163 [2] occurred at disk power-on lifetime: 21731 hours (905 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 00 25 e0 00 00:01:11.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:01:11.000 SET FEATURES [Enable write cache]
ef 00 66 00 00 00 00 00 00 00 00 a0 00 00:01:11.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:01:11.000 SECURITY FREEZE LOCK
c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:00:56.000 SET MULTIPLE MODE
Error 2162 [1] occurred at disk power-on lifetime: 21728 hours (905 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 02 00 00 01 00 00 00 00 00 25 e0 04 00:00:26.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 04 00:00:26.000 SET FEATURES [Enable write cache]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:00:26.000 SECURITY FREEZE LOCK
ef 00 66 00 00 00 00 00 00 00 00 a0 ff 00:00:26.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:26.000 SECURITY FREEZE LOCK
Error 2161 [0] occurred at disk power-on lifetime: 21711 hours (904 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 02 00 00 01 00 00 00 00 00 25 e0 04 00:00:20.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SET FEATURES [Enable write cache]
f5 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SECURITY FREEZE LOCK
ef 00 66 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SECURITY FREEZE LOCK
Error 2160 [7] occurred at disk power-on lifetime: 21684 hours (903 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 02 00 00 01 00 00 00 00 00 25 e0 04 00:00:20.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SET FEATURES [Enable write cache]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SECURITY FREEZE LOCK
ef 00 66 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SECURITY FREEZE LOCK
Error 2159 [6] occurred at disk power-on lifetime: 21731 hours (905 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 00 25 e0 00 00:01:11.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:01:11.000 SET FEATURES [Enable write cache]
ef 00 66 00 00 00 00 00 00 00 00 a0 00 00:01:11.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:01:11.000 SECURITY FREEZE LOCK
c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:00:56.000 SET MULTIPLE MODE
Error 2158 [5] occurred at disk power-on lifetime: 21728 hours (905 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 02 00 00 01 00 00 00 00 00 25 e0 04 00:00:26.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 04 00:00:26.000 SET FEATURES [Enable write cache]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:00:26.000 SECURITY FREEZE LOCK
ef 00 66 00 00 00 00 00 00 00 00 a0 ff 00:00:26.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:26.000 SECURITY FREEZE LOCK
Error 2157 [4] occurred at disk power-on lifetime: 21711 hours (904 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 02 00 00 01 00 00 00 00 00 25 e0 04 00:00:20.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SET FEATURES [Enable write cache]
f5 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SECURITY FREEZE LOCK
ef 00 66 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SECURITY FREEZE LOCK
Error 2156 [3] occurred at disk power-on lifetime: 21684 hours (903 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 01 00 00 00 00 00 25 e0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 02 00 00 01 00 00 00 00 00 25 e0 04 00:00:20.000 READ LOG EXT
ef 00 02 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SET FEATURES [Enable write cache]
f5 00 00 00 00 00 00 00 00 00 00 a0 04 00:00:20.000 SECURITY FREEZE LOCK
ef 00 66 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SET FEATURES [Disable revert defaults]
f5 00 00 00 00 00 00 00 00 00 00 a0 00 00:00:20.000 SECURITY FREEZE LOCK
Warning! SMART Extended Self-test Log Structure error: invalid SMART checksum.
SMART Extended Self-test Log Version: 0 (1 sectors)
Invalid Self-test Log index = 0x2801 (reserved = 0x00)
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 545460846592 4294967296 Not_testing
2 0 545460846592 Not_testing
3 4294967296 0 Not_testing
4 545460846592 4294967296 Not_testing
5 0 545460846592 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 32 Celsius
Power Cycle Min/Max Temperature: --/33 Celsius
Lifetime Min/Max Temperature: --/33 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 10/105 Celsius
Min/Max Temperature Limit: 5/110 Celsius
Temperature History Size (Index): 128 (23)
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
View Git Blame Copy Permalink