80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/HDD/Samsung/HD252/HD252HJ/59EFC363D40A
Andrey Ponomarenko d96e63400c Update of reports (new: 3084, modified: 0)
2021-05-18 23:01:35 +03:00

327 lines
16 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.1-RELEASE amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F1 DT
Device Model: SAMSUNG HD252HJ
Serial Number: --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: 1AC01113
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is: Wed Feb 10 19:06:47 2021 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 3832) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 65) minutes.
Conveyance self-test routine
recommended polling time: ( 8) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 099 002 051 Past 10870
3 Spin_Up_Time POS--- 093 093 011 - 2970
4 Start_Stop_Count -O--CK 096 096 000 - 3665
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
7 Seek_Error_Rate POSR-- 100 100 051 - 0
8 Seek_Time_Performance P-S--K 100 100 015 - 0
9 Power_On_Hours -O--CK 099 099 000 - 4170
10 Spin_Retry_Count PO--CK 100 100 051 - 0
11 Calibration_Retry_Count -O--C- 100 100 000 - 96
12 Power_Cycle_Count -O--CK 097 097 000 - 3269
13 Read_Soft_Error_Rate -OSR-- 099 005 000 - 10153
183 Runtime_Bad_Block -O--CK 100 100 000 - 35
184 End-to-End_Error PO--CK 100 100 000 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 28474
188 Command_Timeout -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 080 056 000 - 20 (Min/Max 13/20)
194 Temperature_Celsius -O---K 075 053 000 - 25 (Min/Max 13/25)
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 4202
196 Reallocated_Event_Count -O--CK 099 099 000 - 30
197 Current_Pending_Sector -O--C- 089 089 000 - 479
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 5
200 Multi_Zone_Error_Rate -O-R-- 099 099 000 - 1679
201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x04 GPL R/O 2 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 2 Write stream error log
0x22 GPL R/O 2 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 29753 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 29753 [0] occurred at disk power-on lifetime: 1866 hours (77 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 58 00 06 00 00 00 00 09 3a e0 00 at LBA = 0x0000093a = 2362
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
39 00 00 00 08 00 00 00 00 09 38 e0 00 00:35:46.830 WRITE MULTIPLE EXT
c6 00 00 00 10 00 00 00 00 00 00 a0 00 00:35:45.910 SET MULTIPLE MODE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:35:45.890 SET FEATURES [Set transfer mode]
ef 00 03 00 0c 00 00 00 00 00 00 a0 00 00:35:45.880 SET FEATURES [Set transfer mode]
00 00 00 00 01 00 00 00 00 00 01 a0 00 00:35:45.820 NOP [Abort queued commands]
Error 29752 [7] occurred at disk power-on lifetime: 1866 hours (77 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 58 00 06 00 00 00 00 09 3a e0 00 6 sectors at LBA = 0x0000093a = 2362
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 00 08 00 00 00 00 09 38 e0 00 00:34:45.350 WRITE DMA EXT
35 00 00 00 08 00 00 00 01 13 68 e0 00 00:34:45.350 WRITE DMA EXT
35 00 00 00 08 00 00 00 01 12 d8 e0 00 00:34:45.350 WRITE DMA EXT
25 00 00 00 08 00 00 00 01 12 d8 e0 00 00:34:45.350 READ DMA EXT
25 00 00 00 08 00 00 00 00 09 38 e0 00 00:34:45.350 READ DMA EXT
Error 29751 [6] occurred at disk power-on lifetime: 1866 hours (77 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 58 00 05 00 00 00 00 f7 83 e0 00 at LBA = 0x0000f783 = 63363
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
39 00 00 00 08 00 00 00 00 f7 80 e0 00 00:31:05.050 WRITE MULTIPLE EXT
29 00 00 00 08 00 00 00 00 f7 88 e0 00 00:31:05.050 READ MULTIPLE EXT
29 00 00 00 08 00 00 00 00 f7 80 e0 00 00:31:05.040 READ MULTIPLE EXT
29 00 00 00 08 00 00 00 00 f2 a0 e0 00 00:31:05.030 READ MULTIPLE EXT
29 00 00 00 08 00 00 00 00 f2 a8 e0 00 00:31:05.030 READ MULTIPLE EXT
Error 29750 [5] occurred at disk power-on lifetime: 1866 hours (77 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 58 00 07 00 00 00 5e fa e1 e0 00 7 sectors at LBA = 0x005efae1 = 6224609
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 00 08 00 00 00 5e fa e0 e0 00 00:28:31.610 WRITE DMA EXT
35 00 00 00 08 00 00 00 5e fa f0 e0 00 00:28:31.610 WRITE DMA EXT
35 00 00 00 08 00 00 00 60 b7 e8 e0 00 00:28:31.610 WRITE DMA EXT
35 00 00 00 08 00 00 00 00 f2 90 e0 00 00:28:31.610 WRITE DMA EXT
35 00 00 00 08 00 00 00 00 f2 a0 e0 00 00:28:31.610 WRITE DMA EXT
Error 29749 [4] occurred at disk power-on lifetime: 1689 hours (70 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 23 d7 ce e1 00 Error: UNC at LBA = 0x0123d7ce = 19126222
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 23 d7 c8 e1 00 05:39:46.320 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:46.300 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 05:39:46.290 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 05:39:46.290 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:46.290 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 29748 [3] occurred at disk power-on lifetime: 1689 hours (70 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 23 d7 ce e1 00 Error: UNC at LBA = 0x0123d7ce = 19126222
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 23 d7 c8 e1 00 05:39:44.350 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:43.540 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 05:39:43.530 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 05:39:43.530 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:43.530 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 29747 [2] occurred at disk power-on lifetime: 1689 hours (70 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 23 d7 ce e1 00 Error: UNC at LBA = 0x0123d7ce = 19126222
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 23 d7 c8 e1 00 05:39:41.600 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:41.590 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 05:39:41.580 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 05:39:41.580 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:41.580 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 29746 [1] occurred at disk power-on lifetime: 1689 hours (70 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 01 23 d7 ce e1 00 Error: UNC at LBA = 0x0123d7ce = 19126222
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 08 00 00 00 23 d7 c8 e1 00 05:39:39.640 READ DMA
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:38.830 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 05:39:38.820 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 00 05:39:38.820 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 05:39:38.820 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 26 Celsius
Power Cycle Min/Max Temperature: --/26 Celsius
Lifetime Min/Max Temperature: --/60 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -4/72 Celsius
Min/Max Temperature Limit: -9/77 Celsius
Temperature History Size (Index): 128 (66)
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: Input/output error
Read Device Statistics page 0x00 failed
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 6 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
View Git Blame Copy Permalink