mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
100 lines
5.0 KiB
Plaintext
100 lines
5.0 KiB
Plaintext
smartctl 7.1 2019-12-30 r5022 [x86_64-unknown-openbsd6.9] (local build)
|
|
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Model Family: SAMSUNG SpinPoint F1 DT
|
|
Device Model: SAMSUNG HD322HJ
|
|
Serial Number: --
|
|
LU WWN Device Id: 5 0024e9 ...
|
|
Firmware Version: 1AC01118
|
|
User Capacity: 320,072,933,376 bytes [320 GB]
|
|
Sector Size: 512 bytes logical/physical
|
|
Device is: In smartctl database [for details use: -P show]
|
|
ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
|
|
Local Time is: Sun Jul 16 02:31:53 2023 EEST
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART overall-health self-assessment test result: PASSED
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x00) Offline data collection activity
|
|
was never started.
|
|
Auto Offline Data Collection: Disabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: ( 4123) seconds.
|
|
Offline data collection
|
|
capabilities: (0x7b) SMART execute Offline immediate.
|
|
Auto Offline data collection on/off support.
|
|
Suspend Offline collection upon new
|
|
command.
|
|
Offline surface scan supported.
|
|
Self-test supported.
|
|
Conveyance Self-test supported.
|
|
Selective Self-test supported.
|
|
SMART capabilities: (0x0003) Saves SMART data before entering
|
|
power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x01) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 70) minutes.
|
|
Conveyance self-test routine
|
|
recommended polling time: ( 8) minutes.
|
|
SCT capabilities: (0x003f) SCT Status supported.
|
|
SCT Error Recovery Control supported.
|
|
SCT Feature Control supported.
|
|
SCT Data Table supported.
|
|
|
|
SMART Attributes Data Structure revision number: 16
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
|
|
3 Spin_Up_Time 0x0007 094 094 011 Pre-fail Always - 2760
|
|
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1259
|
|
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
|
|
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
|
|
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
|
|
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 23374
|
|
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
|
|
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
|
|
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1256
|
|
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0
|
|
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
|
|
184 End-to-End_Error 0x0033 100 100 000 Pre-fail Always - 0
|
|
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
|
|
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
|
|
190 Airflow_Temperature_Cel 0x0022 067 063 000 Old_age Always - 33 (Min/Max 32/33)
|
|
194 Temperature_Celsius 0x0022 067 061 000 Old_age Always - 33 (Min/Max 32/35)
|
|
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 954910
|
|
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
|
|
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
|
|
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
|
|
199 UDMA_CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
|
|
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
|
|
201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0
|
|
|
|
SMART Error Log Version: 1
|
|
No Errors Logged
|
|
|
|
SMART Self-test log structure revision number 1
|
|
No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
|
SMART Selective self-test log data structure revision number 1
|
|
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|
1 0 0 Not_testing
|
|
2 0 0 Not_testing
|
|
3 0 0 Not_testing
|
|
4 0 0 Not_testing
|
|
5 0 0 Not_testing
|
|
Selective self-test flags (0x0):
|
|
After scanning selected spans, do NOT read-scan remainder of disk.
|
|
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|