1
0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Files
SMART-open-study/HDD/Samsung/HE103/HE103UJ/D35D28A4F303
2025-01-05 01:57:11 +03:00

324 lines
16 KiB
Plaintext

smartctl 7.4 2023-08-01 r5530 [FreeBSD 13.2-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F1 RE
Device Model: SAMSUNG HE103UJ
Serial Number: --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: 1AA01114
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database 7.3/5528
ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is: Tue Jul 30 22:53:03 2024 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (11733) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 196) minutes.
Conveyance self-test routine
recommended polling time: ( 21) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 100 099 051 - 47
3 Spin_Up_Time POS--- 076 076 011 - 8060
4 Start_Stop_Count -O--CK 100 100 000 - 61
5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0
7 Seek_Error_Rate POSR-- 100 100 051 - 0
8 Seek_Time_Performance P-S--K 100 100 015 - 0
9 Power_On_Hours -O--CK 093 093 000 - 34185
10 Spin_Retry_Count PO--CK 100 100 051 - 0
11 Calibration_Retry_Count -O--C- 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 55
13 Read_Soft_Error_Rate -OSR-- 100 099 000 - 0
183 Runtime_Bad_Block -O--CK 100 100 000 - 0
184 End-to-End_Error PO--CK 047 047 000 - 53
187 Reported_Uncorrect -O--CK 100 100 000 - 134
188 Command_Timeout -O--CK 100 100 000 - 5
190 Airflow_Temperature_Cel -O---K 066 055 000 - 34 (Min/Max 20/35)
194 Temperature_Celsius -O---K 066 054 000 - 34 (Min/Max 20/37)
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 42080
196 Reallocated_Event_Count -O--CK 098 098 000 - 73
197 Current_Pending_Sector -O--C- 100 099 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 100 099 000 - 575
200 Multi_Zone_Error_Rate -O-R-- 100 099 000 - 7
201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x04 GPL R/O 2 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 2 Write stream error log
0x22 GPL R/O 2 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 1504 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1504 [7] occurred at disk power-on lifetime: 29022 hours (1209 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
96 -- 51 00 00 00 00 0b d7 7e cd e0 00 Error: ICRC, IDNF, ABRT, NM at LBA = 0x0bd77ecd = 198672077
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 aa 03 01 00 00 00 0b d7 7e cb e0 00 9d+03:35:53.180 READ DMA EXT
35 aa 03 01 00 00 00 02 83 3f 58 e0 00 9d+03:35:53.070 WRITE DMA EXT
35 aa 03 00 01 00 00 6f 95 63 9f e0 00 9d+03:35:53.010 WRITE DMA EXT
35 aa 03 01 00 00 00 02 88 f1 a1 e0 00 9d+03:35:53.010 WRITE DMA EXT
25 aa 03 01 00 00 00 0b d7 7d cb e0 00 9d+03:35:52.950 READ DMA EXT
Error 1503 [6] occurred at disk power-on lifetime: 29022 hours (1209 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
96 -- 51 00 00 00 00 0b d7 7e cd e0 00 Error: ICRC, IDNF, ABRT, NM at LBA = 0x0bd77ecd = 198672077
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 aa 03 01 00 00 00 0b d7 7e 3a e0 00 9d+03:33:27.900 READ DMA EXT
35 aa 03 01 00 00 00 02 72 0f 9e e0 00 9d+03:33:27.780 WRITE DMA EXT
35 aa 03 00 01 00 00 6f 95 60 a2 e0 00 9d+03:33:27.720 WRITE DMA EXT
35 aa 03 01 00 00 00 02 68 50 54 e0 00 9d+03:33:27.710 WRITE DMA EXT
25 aa 03 01 00 00 00 0b d7 7d 3a e0 00 9d+03:33:27.650 READ DMA EXT
Error 1502 [5] occurred at disk power-on lifetime: 29022 hours (1209 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
96 -- 51 00 00 00 00 0b d7 7e cd e0 00 Error: ICRC, IDNF, ABRT, NM at LBA = 0x0bd77ecd = 198672077
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 aa 03 01 00 00 00 0b d7 7e c9 e0 00 9d+03:31:39.340 READ DMA EXT
35 aa 03 00 01 00 00 6f 95 63 90 e0 00 9d+03:31:39.250 WRITE DMA EXT
35 aa 03 00 d3 00 00 01 f9 f2 cc e0 00 9d+03:31:39.250 WRITE DMA EXT
35 aa 03 01 00 00 00 01 f2 1d 50 e0 00 9d+03:31:39.240 WRITE DMA EXT
25 aa 03 01 00 00 00 0b d7 7d c9 e0 00 9d+03:31:39.140 READ DMA EXT
Error 1501 [4] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 0b d7 7e cc 40 00 at LBA = 0x0bd77ecc = 198672076
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 03 00 80 00 00 00 d7 7e 68 40 00 5d+02:34:43.170 READ FPDMA QUEUED
ef 00 03 00 46 00 00 00 00 00 00 00 00 5d+02:34:43.160 SET FEATURES [Set transfer mode]
ef 00 03 00 0c 00 00 00 00 00 00 00 00 5d+02:34:43.150 SET FEATURES [Set transfer mode]
ef 00 03 00 00 00 00 00 00 00 00 00 00 5d+02:34:43.140 SET FEATURES [Set transfer mode]
10 00 00 00 00 00 00 00 00 00 00 00 00 5d+02:34:42.920 RECALIBRATE [OBS-4]
Error 1500 [3] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 0b d7 7e cc 40 00 at LBA = 0x0bd77ecc = 198672076
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 03 00 80 00 00 00 d7 7e 68 40 00 5d+02:34:39.160 READ FPDMA QUEUED
ef 00 03 00 46 00 00 00 00 00 00 00 00 5d+02:34:39.150 SET FEATURES [Set transfer mode]
ef 00 03 00 0c 00 00 00 00 00 00 00 00 5d+02:34:39.140 SET FEATURES [Set transfer mode]
ef 00 03 00 00 00 00 00 00 00 00 00 00 5d+02:34:39.130 SET FEATURES [Set transfer mode]
10 00 00 00 00 00 00 00 00 00 00 00 00 5d+02:34:38.930 RECALIBRATE [OBS-4]
Error 1499 [2] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 0b d7 7e cc 40 00 at LBA = 0x0bd77ecc = 198672076
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 03 00 80 00 00 00 d7 7e 68 40 00 5d+02:34:35.120 READ FPDMA QUEUED
ef 00 03 00 46 00 00 00 00 00 00 00 00 5d+02:34:35.110 SET FEATURES [Set transfer mode]
ef 00 03 00 0c 00 00 00 00 00 00 00 00 5d+02:34:35.100 SET FEATURES [Set transfer mode]
ef 00 03 00 00 00 00 00 00 00 00 00 00 5d+02:34:35.090 SET FEATURES [Set transfer mode]
10 00 00 00 00 00 00 00 00 00 00 00 00 5d+02:34:34.890 RECALIBRATE [OBS-4]
Error 1498 [1] occurred at disk power-on lifetime: 27371 hours (1140 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 0b d7 7e cc 40 00 at LBA = 0x0bd77ecc = 198672076
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 80 00 00 00 d7 7e 68 40 00 5d+02:34:31.130 READ FPDMA QUEUED
e7 00 00 00 00 00 00 00 00 00 00 40 00 5d+02:34:30.800 FLUSH CACHE
34 00 00 00 01 00 00 74 6e 00 01 40 00 5d+02:34:30.790 WRITE SECTORS(S) EXT
40 00 00 00 01 00 00 00 00 00 00 40 00 5d+02:34:30.670 READ VERIFY SECTOR(S)
61 00 00 00 08 00 00 00 20 02 d0 40 00 5d+02:21:12.070 WRITE FPDMA QUEUED
Error 1497 [0] occurred at disk power-on lifetime: 27271 hours (1136 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 0b d7 7e cc 40 00 at LBA = 0x0bd77ecc = 198672076
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 03 00 80 00 00 00 d7 7e 68 40 00 22:12:50.560 READ FPDMA QUEUED
ef 00 03 00 46 00 00 00 00 00 00 00 00 22:12:50.550 SET FEATURES [Set transfer mode]
ef 00 03 00 0c 00 00 00 00 00 00 00 00 22:12:50.540 SET FEATURES [Set transfer mode]
ef 00 03 00 00 00 00 00 00 00 00 00 00 22:12:50.530 SET FEATURES [Set transfer mode]
10 00 00 00 00 00 00 00 00 00 00 00 00 22:12:50.330 RECALIBRATE [OBS-4]
SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 34 Celsius
Power Cycle Min/Max Temperature: --/36 Celsius
Lifetime Min/Max Temperature: --/58 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -4/72 Celsius
Min/Max Temperature Limit: -9/77 Celsius
Temperature History Size (Index): 128 (98)
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: Input/output error
Read Device Statistics page 0x00 failed
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC