mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
155 lines
7.6 KiB
Plaintext
155 lines
7.6 KiB
Plaintext
smartctl 7.4 2023-08-01 r5530 [OpenBSD 7.6 amd64] (local build)
|
|
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Model Family: Seagate BarraCuda 3.5 (SMR)
|
|
Device Model: ST2000DM008-2FR102
|
|
Serial Number: --
|
|
LU WWN Device Id: 5 000c50 ...
|
|
Firmware Version: 0001
|
|
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
|
|
Sector Sizes: 512 bytes logical, 4096 bytes physical
|
|
Rotation Rate: 7200 rpm
|
|
Form Factor: 3.5 inches
|
|
TRIM Command: Available
|
|
Device is: In smartctl database 7.3/5528
|
|
ATA Version is: ACS-3 T13/2161-D revision 5
|
|
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
|
|
Local Time is: Mon Sep 23 21:11:13 2024 CDT
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART Status not supported: Incomplete response, ATA output registers missing
|
|
SMART overall-health self-assessment test result: PASSED
|
|
Warning: This result is based on an Attribute check.
|
|
See vendor-specific Attribute list for marginal Attributes.
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x00) Offline data collection activity
|
|
was never started.
|
|
Auto Offline Data Collection: Disabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: ( 0) seconds.
|
|
Offline data collection
|
|
capabilities: (0x73) SMART execute Offline immediate.
|
|
Auto Offline data collection on/off support.
|
|
Suspend Offline collection upon new
|
|
command.
|
|
No Offline surface scan supported.
|
|
Self-test supported.
|
|
Conveyance Self-test supported.
|
|
Selective Self-test supported.
|
|
SMART capabilities: (0x0003) Saves SMART data before entering
|
|
power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x01) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 1) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 203) minutes.
|
|
Conveyance self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
SCT capabilities: (0x30a5) SCT Status supported.
|
|
SCT Data Table supported.
|
|
|
|
SMART Attributes Data Structure revision number: 10
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|
1 Raw_Read_Error_Rate 0x000f 100 064 006 Pre-fail Always - 1109255
|
|
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0
|
|
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 259
|
|
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
|
|
7 Seek_Error_Rate 0x000f 085 060 045 Pre-fail Always - 315925860
|
|
9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 12241h+58m+44.472s
|
|
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
|
|
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 259
|
|
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
|
|
184 End-to-End_Error 0x0032 099 099 099 Old_age Always FAILING_NOW 1
|
|
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
|
|
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
|
|
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
|
|
190 Airflow_Temperature_Cel 0x0022 070 061 040 Old_age Always - 30 (Min/Max 27/30)
|
|
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
|
|
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 108
|
|
193 Load_Cycle_Count 0x0032 008 008 000 Old_age Always - 185651
|
|
194 Temperature_Celsius 0x0022 030 040 000 Old_age Always - 30 (0 17 0 0 0)
|
|
195 Hardware_ECC_Recovered 0x001a 100 064 000 Old_age Always - 1109255
|
|
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
|
|
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
|
|
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
|
|
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 2871h+35m+24.878s
|
|
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 32890914444
|
|
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 14524051096
|
|
|
|
SMART Error Log Version: 1
|
|
ATA Error Count: 2
|
|
CR = Command Register [HEX]
|
|
FR = Features Register [HEX]
|
|
SC = Sector Count Register [HEX]
|
|
SN = Sector Number Register [HEX]
|
|
CL = Cylinder Low Register [HEX]
|
|
CH = Cylinder High Register [HEX]
|
|
DH = Device/Head Register [HEX]
|
|
DC = Device Command Register [HEX]
|
|
ER = Error register [HEX]
|
|
ST = Status register [HEX]
|
|
Powered_Up_Time is measured from power on, and printed as
|
|
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
|
|
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
|
|
|
|
Error 2 occurred at disk power-on lifetime: 2810 hours (117 days + 2 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 53 00 e0 1f 3d 00
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
ea 00 00 00 00 00 a0 00 1d+11:24:47.560 FLUSH CACHE EXT
|
|
61 00 20 00 30 01 40 00 1d+11:24:47.556 WRITE FPDMA QUEUED
|
|
61 00 20 c0 30 01 40 00 1d+11:24:47.555 WRITE FPDMA QUEUED
|
|
61 00 40 60 32 01 40 00 1d+11:24:47.555 WRITE FPDMA QUEUED
|
|
61 00 20 00 34 01 40 00 1d+11:24:47.555 WRITE FPDMA QUEUED
|
|
|
|
Error 1 occurred at disk power-on lifetime: 2789 hours (116 days + 5 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
04 73 04 80 87 80 40 Device Fault; Error: ABRT at LBA = 0x00808780 = 8423296
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
61 00 20 c0 2e 1d 40 00 14:56:24.962 WRITE FPDMA QUEUED
|
|
61 00 20 c0 2e 3d 40 00 14:56:24.962 WRITE FPDMA QUEUED
|
|
61 00 00 ff ff ff 4f 00 14:56:24.962 WRITE FPDMA QUEUED
|
|
61 00 00 ff ff ff 4f 00 14:56:24.962 WRITE FPDMA QUEUED
|
|
61 00 90 ff ff ff 4f 00 14:56:24.962 WRITE FPDMA QUEUED
|
|
|
|
SMART Self-test log structure revision number 1
|
|
No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
|
SMART Selective self-test log data structure revision number 1
|
|
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|
1 0 0 Not_testing
|
|
2 0 0 Not_testing
|
|
3 0 0 Not_testing
|
|
4 0 0 Not_testing
|
|
5 0 0 Not_testing
|
|
Selective self-test flags (0x0):
|
|
After scanning selected spans, do NOT read-scan remainder of disk.
|
|
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|
|
The above only provides legacy SMART information - try 'smartctl -x' for more
|
|
|