80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/HDD/Seagate/ST3808/ST380815AS/CBE13F11FD92
Andrey Ponomarenko b1c41e7edc Update of reports (new: 3637, modified: 0)
2022-03-18 23:39:11 +03:00

290 lines
15 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST380815AS
Serial Number: --
Firmware Version: 4.AAB
User Capacity: 80,026,361,856 bytes [80.0 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Mon Jun 28 09:24:15 2021 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0
3 Spin_Up_Time PO---- 098 097 000 - 0
4 Start_Stop_Count -O--CK 099 099 020 - 1390
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 078 060 030 - 70698361
9 Power_On_Hours -O--CK 099 099 000 - 1281
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 099 099 020 - 1394
187 Reported_Uncorrect -O--CK 071 071 000 - 29
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 057 048 045 - 43 (Min/Max 32/43)
194 Temperature_Celsius -O---K 043 052 000 - 43 (0 16 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 086 071 000 - 35586
197 Current_Pending_Sector -O--C- 100 100 000 - 2
198 Offline_Uncorrectable ----C- 100 100 000 - 2
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x23 GPL,SL R/O 1 Delayed sector log [OBS-8]
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL,SL VS 1 Device vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL,SL VS 101 Device vendor specific log
0xa8 GPL,SL VS 20 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
0xff GPL - 23040 Reserved
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 30 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 30 [9] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 06 e2 00 00:08:20.769 READ DMA
20 00 03 00 01 00 02 8a 00 85 05 e2 00 00:08:17.245 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 05 00 00 00:08:17.230 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 05 00 00 00:08:17.149 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 05 e2 00 00:08:17.048 READ DMA
Error 29 [8] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 05 e2 00 00:08:20.769 READ DMA
20 00 03 00 01 00 02 8a 00 85 04 e2 00 00:08:17.245 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 04 00 00 00:08:17.230 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 04 00 00 00:08:17.149 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 04 e2 00 00:08:17.048 READ DMA
Error 28 [7] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 08 e2 00 00:08:32.213 READ DMA
20 00 03 00 01 00 02 8a 00 85 07 e2 00 00:08:32.197 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 07 00 00 00:08:32.117 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 07 00 00 00:08:32.016 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 07 e2 00 00:08:28.400 READ DMA
Error 27 [6] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 07 e2 00 00:08:20.769 READ DMA
20 00 03 00 01 00 02 8a 00 85 06 e2 00 00:08:17.245 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 06 00 00 00:08:17.230 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 06 00 00 00:08:17.149 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 06 e2 00 00:08:28.400 READ DMA
Error 26 [5] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 06 e2 00 00:08:20.769 READ DMA
20 00 03 00 01 00 02 8a 00 85 05 e2 00 00:08:17.245 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 05 00 00 00:08:17.230 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 05 00 00 00:08:17.149 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 05 e2 00 00:08:17.048 READ DMA
Error 25 [4] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 05 e2 00 00:08:20.769 READ DMA
20 00 03 00 01 00 02 8a 00 85 04 e2 00 00:08:17.245 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 04 00 00 00:08:17.230 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 04 00 00 00:08:17.149 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 04 e2 00 00:08:17.048 READ DMA
Error 24 [3] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 08 e2 00 00:08:32.213 READ DMA
20 00 03 00 01 00 02 8a 00 85 07 e2 00 00:08:32.197 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 07 00 00 00:08:32.117 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 07 00 00 00:08:32.016 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 07 e2 00 00:08:28.400 READ DMA
Error 23 [2] occurred at disk power-on lifetime: 80 hours (3 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 02 8a 00 85 0d e2 00 Error: UNC at LBA = 0x28a00850d = 10905224461
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 03 00 20 00 02 8a 00 85 07 e2 00 00:08:20.769 READ DMA
20 00 03 00 01 00 02 8a 00 85 06 e2 00 00:08:17.245 READ SECTOR(S)
00 00 00 00 20 00 02 8a 00 85 06 00 00 00:08:17.230 NOP [Abort queued commands]
00 00 00 00 20 00 02 8a 00 85 06 00 00 00:08:17.149 NOP [Abort queued commands]
c8 00 03 00 20 00 02 8a 00 85 06 e2 00 00:08:28.400 READ DMA
SMART Extended Self-test Log Version: 1 (1 sectors)
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Commands not supported
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 13 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
View Git Blame Copy Permalink