mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
89 lines
4.1 KiB
Plaintext
89 lines
4.1 KiB
Plaintext
smartctl 7.2 2020-12-30 r5155 [OpenBSD 7.0 amd64] (local build)
|
|
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Device Model: 8GB SATA Flash Drive
|
|
Serial Number: --
|
|
Firmware Version: SFPS921D
|
|
User Capacity: 8,012,390,400 bytes [8.01 GB]
|
|
Sector Size: 512 bytes logical/physical
|
|
Rotation Rate: Solid State Device
|
|
Form Factor: < 1.8 inches
|
|
TRIM Command: Available
|
|
Device is: Not in smartctl database [for details use: -P showall]
|
|
ATA Version is: ACS-3 (minor revision not indicated)
|
|
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
|
|
Local Time is: Sun Jan 23 16:30:21 2022 CST
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART Status not supported: Incomplete response, ATA output registers missing
|
|
SMART overall-health self-assessment test result: PASSED
|
|
Warning: This result is based on an Attribute check.
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x00) Offline data collection activity
|
|
was never started.
|
|
Auto Offline Data Collection: Disabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: ( 30) seconds.
|
|
Offline data collection
|
|
capabilities: (0x7b) SMART execute Offline immediate.
|
|
Auto Offline data collection on/off support.
|
|
Suspend Offline collection upon new
|
|
command.
|
|
Offline surface scan supported.
|
|
Self-test supported.
|
|
Conveyance Self-test supported.
|
|
Selective Self-test supported.
|
|
SMART capabilities: (0x0003) Saves SMART data before entering
|
|
power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x01) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 1) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
Conveyance self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
|
|
SMART Attributes Data Structure revision number: 16
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1929
|
|
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 307
|
|
163 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 7
|
|
164 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 3
|
|
166 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 0
|
|
167 Unknown_Attribute 0x0022 100 100 000 Old_age Always - 0
|
|
168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 0
|
|
175 Program_Fail_Count_Chip 0x0000 100 100 000 Old_age Offline - 0
|
|
192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 7
|
|
194 Temperature_Celsius 0x0023 070 070 000 Pre-fail Always - 30
|
|
231 Unknown_SSD_Attribute 0x0013 100 100 000 Pre-fail Always - 99
|
|
241 Total_LBAs_Written 0x0012 100 100 000 Old_age Always - 52146772
|
|
|
|
SMART Error Log Version: 1
|
|
No Errors Logged
|
|
|
|
SMART Self-test log structure revision number 1
|
|
No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
|
SMART Selective self-test log data structure revision number 0
|
|
Note: revision number not 1 implies that no selective self-test has ever been run
|
|
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|
1 0 0 Not_testing
|
|
2 0 0 Not_testing
|
|
3 0 0 Not_testing
|
|
4 0 0 Not_testing
|
|
5 0 0 Not_testing
|
|
Selective self-test flags (0x0):
|
|
After scanning selected spans, do NOT read-scan remainder of disk.
|
|
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|