mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
205 lines
8.5 KiB
Plaintext
205 lines
8.5 KiB
Plaintext
smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p7 amd64] (local build)
|
|
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Device Model: LITEONIT LAT-256M3S
|
|
Serial Number: --
|
|
LU WWN Device Id: 5 000000 ...
|
|
Firmware Version: VBA2
|
|
User Capacity: 256,060,514,304 bytes [256 GB]
|
|
Sector Size: 512 bytes logical/physical
|
|
Rotation Rate: Solid State Device
|
|
TRIM Command: Available
|
|
Device is: Not in smartctl database 7.3/5319
|
|
ATA Version is: ATA8-ACS, ATA/ATAPI-7 T13/1532D revision 4a
|
|
SATA Version is: SATA 3.0, 6.0 Gb/s
|
|
Local Time is: Thu May 18 19:28:39 2023 NZST
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
AAM feature is: Disabled
|
|
APM feature is: Unavailable
|
|
Rd look-ahead is: Enabled
|
|
Write cache is: Enabled
|
|
DSN feature is: Unavailable
|
|
ATA Security is: Disabled, NOT FROZEN [SEC1]
|
|
Wt Cache Reorder: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART overall-health self-assessment test result: PASSED
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x00) Offline data collection activity
|
|
was never started.
|
|
Auto Offline Data Collection: Disabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: ( 10) seconds.
|
|
Offline data collection
|
|
capabilities: (0x15) SMART execute Offline immediate.
|
|
No Auto Offline data collection support.
|
|
Abort Offline collection upon new
|
|
command.
|
|
No Offline surface scan supported.
|
|
Self-test supported.
|
|
No Conveyance Self-test supported.
|
|
No Selective Self-test supported.
|
|
SMART capabilities: (0x0002) Does not save SMART data before
|
|
entering power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x00) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 10) minutes.
|
|
SCT capabilities: (0x003d) SCT Status supported.
|
|
SCT Error Recovery Control supported.
|
|
SCT Feature Control supported.
|
|
SCT Data Table supported.
|
|
|
|
SMART Attributes Data Structure revision number: 1
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
|
|
1 Raw_Read_Error_Rate PO---- 100 100 070 - 0
|
|
5 Reallocated_Sector_Ct PO---- 100 100 000 - 0
|
|
9 Power_On_Hours -O---- 100 100 000 - 28730
|
|
12 Power_Cycle_Count -O---- 100 100 000 - 731
|
|
178 Used_Rsvd_Blk_Cnt_Chip PO---- 100 100 000 - 0
|
|
187 Reported_Uncorrect -O---- 100 100 000 - 0
|
|
192 Power-Off_Retract_Count PO---- 100 100 000 - 8
|
|
||||||_ K auto-keep
|
|
|||||__ C event count
|
|
||||___ R error rate
|
|
|||____ S speed/performance
|
|
||_____ O updated online
|
|
|______ P prefailure warning
|
|
|
|
General Purpose Log Directory Version 0
|
|
SMART Log Directory Version 0
|
|
Address Access R/W Size Description
|
|
0x00 GPL,SL R/O 1 Log Directory
|
|
0x01 GPL,SL R/O 1 Summary SMART error log
|
|
0x06 GPL,SL R/O 1 SMART self-test log
|
|
0x07 GPL,SL R/O 1 Extended self-test log
|
|
0x10 GPL,SL R/O 1 NCQ Command Error log
|
|
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
|
|
0x80-0x9f GPL,SL R/W 1 Host vendor specific log
|
|
0xe0 GPL,SL R/W 1 SCT Command/Status
|
|
0xe1 GPL,SL R/W 1 SCT Data Transfer
|
|
|
|
SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
|
|
|
|
SMART Error Log Version: 1
|
|
Warning: ATA error count 0 inconsistent with error log pointer 1
|
|
|
|
ATA Error Count: 0
|
|
CR = Command Register [HEX]
|
|
FR = Features Register [HEX]
|
|
SC = Sector Count Register [HEX]
|
|
SN = Sector Number Register [HEX]
|
|
CL = Cylinder Low Register [HEX]
|
|
CH = Cylinder High Register [HEX]
|
|
DH = Device/Head Register [HEX]
|
|
DC = Device Command Register [HEX]
|
|
ER = Error register [HEX]
|
|
ST = Status register [HEX]
|
|
Powered_Up_Time is measured from power on, and printed as
|
|
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
|
|
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
|
|
|
|
Error 0 occurred at disk power-on lifetime: 768 hours (32 days + 0 hours)
|
|
When the command that caused the error occurred, the device was in an unknown state.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
00 cf 00 00 01 da 37
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
cf 00 00 12 01 da 37 00 1d+06:25:20.381 [RESERVED]
|
|
cf 00 00 e0 01 da 37 00 1d+09:59:25.437 [RESERVED]
|
|
cf 00 00 e0 01 da 37 00 1d+09:51:46.685 [RESERVED]
|
|
cf 00 00 e0 01 da 37 00 1d+09:41:56.861 [RESERVED]
|
|
cf 00 00 e0 01 da 37 00 1d+09:32:07.037 [RESERVED]
|
|
|
|
Error -3 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
|
|
When the command that caused the error occurred, the device was in an unknown state.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
00 00 00 00 00 00 00
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
00 03 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
|
|
|
|
Error -4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
|
|
When the command that caused the error occurred, the device was in an unknown state.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
00 da 00 00 00 00 01
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
00 06 00 00 00 00 00 a0 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
|
|
da 06 00 00 00 12 01 96 7d+09:03:10.647 GET MEDIA STATUS [OBS-8]
|
|
da 06 00 00 00 12 01 8f 7d+09:03:10.647 GET MEDIA STATUS [OBS-8]
|
|
da 00 00 00 00 12 01 00 7d+09:03:10.647 GET MEDIA STATUS [OBS-8]
|
|
|
|
SMART Extended Self-test Log Version: 1 (1 sectors)
|
|
No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
|
Selective Self-tests/Logging not supported
|
|
|
|
SCT Status Version: 3
|
|
SCT Version (vendor specific): 1 (0x0001)
|
|
Device State: Active (0)
|
|
Current Temperature: ? Celsius
|
|
Power Cycle Min/Max Temperature: ?/ ? Celsius
|
|
Lifetime Min/Max Temperature: ?/ ? Celsius
|
|
Under/Over Temperature Limit Count: 0/0
|
|
|
|
SCT Temperature History Version: 2
|
|
Temperature Sampling Period: 0 minutes
|
|
Temperature Logging Interval: 0 minutes
|
|
Min/Max recommended Temperature: ?/ ? Celsius
|
|
Min/Max Temperature Limit: ?/ ? Celsius
|
|
Temperature History Size (Index): 128 (0)
|
|
|
|
SCT Error Recovery Control:
|
|
Read: 2 (0.2 seconds)
|
|
Write: 2 (0.2 seconds)
|
|
|
|
Device Statistics (GP/SMART Log 0x04) not supported
|
|
|
|
Pending Defects log (GP Log 0x0c) not supported
|
|
|
|
SATA Phy Event Counters (GP Log 0x11)
|
|
ID Size Value Description
|
|
0x0001 2 0 Command failed due to ICRC error
|
|
0x0002 2 0 R_ERR response for data FIS
|
|
0x0003 2 0 R_ERR response for device-to-host data FIS
|
|
0x0004 2 0 R_ERR response for host-to-device data FIS
|
|
0x0005 2 0 R_ERR response for non-data FIS
|
|
0x0006 2 0 R_ERR response for device-to-host non-data FIS
|
|
0x0007 2 0 R_ERR response for host-to-device non-data FIS
|
|
0x0008 2 0 Device-to-host non-data FIS retries
|
|
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
|
|
0x000a 2 24 Device-to-host register FISes sent due to a COMRESET
|
|
0x000b 2 0 CRC errors within host-to-device FIS
|
|
0x000d 2 0 Non-CRC errors within host-to-device FIS
|
|
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
|
|
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
|
|
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
|
|
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
|
|
|