80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/SSD/Transcend/TS64/TS64GSSD340/B25ADB341E5E
Andrey Ponomarenko b1c41e7edc Update of reports (new: 3637, modified: 0)
2022-03-18 23:39:11 +03:00

328 lines
16 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.1-RELEASE-p19-HBSD amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: JMicron/Maxiotek based SSDs
Device Model: TS64GSSD340
Serial Number: --
LU WWN Device Id: 5 000000 ...
Firmware Version: SVN263
User Capacity: 64,023,257,088 bytes [64.0 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: < 1.8 inches
TRIM Command: Available
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 3.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jul 24 16:16:38 2021 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 32) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 1) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0
2 Throughput_Performance P-S--- 100 100 050 - 0
3 Unknown_JMF_Attribute POS--- 100 100 050 - 0
5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0
7 Unknown_JMF_Attribute PO-R-- 100 100 050 - 0
8 Unknown_JMF_Attribute P-S--- 100 100 050 - 0
9 Power_On_Hours -O--C- 100 100 000 - 26751
10 Unknown_JMF_Attribute PO--C- 100 100 050 - 0
12 Power_Cycle_Count -O--C- 100 100 000 - 112
167 Unknown_JMF_Attribute -O---K 100 100 000 - 0
168 SATA_Phy_Error_Count -O--C- 100 100 000 - 1021
169 Unknown_JMF_Attribute PO--C- 100 100 010 - 851968
170 Bad_Block_Count PO--C- 100 100 010 - 0 0 0
173 Erase_Count -O--C- 182 182 000 - 309 438 198
175 Bad_Cluster_Table_Count PO--C- 100 100 010 - 0
192 Unexpect_Power_Loss_Ct -O--C- 100 100 000 - 53
194 Temperature_Celsius -O---K 060 060 030 - 40 (Min/Max 35/40)
197 Current_Pending_Sector -O--C- 100 100 000 - 0
240 Unknown_JMF_Attribute PO--C- 100 100 050 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 51 Comprehensive SMART error log
0x03 GPL R/O 64 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 345 (device log contains only the most recent 256 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 345 [88] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 08 30 a0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
47 00 00 00 01 00 00 00 00 08 30 a0 08 00:04:57.200 READ LOG DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:04:57.200 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 00:04:57.200 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:04:57.200 IDENTIFY DEVICE
00 00 00 00 00 00 00 00 00 00 00 00 04 00:04:57.100 NOP [Abort queued commands]
Error 344 [87] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 06 00 00 00 44 10 da e7 00 Error: ICRC, ABRT 6 sectors at LBA = 0x074410da = 121901274
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 06 00 00 00 44 10 da e7 08 00:11:21.600 READ DMA
c8 00 00 00 01 00 00 07 44 10 d9 e7 08 00:11:21.600 READ DMA
c8 00 00 00 01 00 00 00 44 10 d8 e7 08 00:11:21.600 READ DMA
c8 00 00 00 06 00 00 07 44 10 d2 e7 08 00:11:21.600 READ DMA
c8 00 00 00 01 00 00 07 44 10 d1 e7 08 00:11:21.600 READ DMA
Error 343 [86] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 08 30 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 08 30 a0 08 00:07:46.500 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:07:46.500 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 00:07:46.500 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:07:46.500 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 08 00:07:46.500 SET FEATURES [Set transfer mode]
Error 342 [85] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 00 00 00 00 a0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:05:00.300 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 08 00:05:00.300 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 08 30 a0 08 00:05:00.300 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:05:00.300 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 00:05:00.300 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 341 [84] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 08 30 a0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
47 00 00 00 01 00 00 00 00 08 30 a0 08 00:04:57.200 READ LOG DMA EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:04:57.200 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 00:04:57.200 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:04:57.200 IDENTIFY DEVICE
00 00 00 00 00 00 00 00 00 00 00 00 04 00:04:57.100 NOP [Abort queued commands]
Error 340 [83] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 06 00 00 00 44 10 da e7 00 Error: ICRC, ABRT 6 sectors at LBA = 0x074410da = 121901274
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
c8 00 00 00 06 00 00 00 44 10 da e7 08 00:11:21.600 READ DMA
c8 00 00 00 01 00 00 07 44 10 d9 e7 08 00:11:21.600 READ DMA
c8 00 00 00 01 00 00 00 44 10 d8 e7 08 00:11:21.600 READ DMA
c8 00 00 00 06 00 00 07 44 10 d2 e7 08 00:11:21.600 READ DMA
c8 00 00 00 01 00 00 07 44 10 d1 e7 08 00:11:21.600 READ DMA
Error 339 [82] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 08 30 a0 00 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 08 30 a0 08 00:07:46.500 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:07:46.500 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 00:07:46.500 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:07:46.500 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 08 00:07:46.500 SET FEATURES [Set transfer mode]
Error 338 [81] occurred at disk power-on lifetime: 5017 hours (209 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 00 00 00 00 00 00 00 a0 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:05:00.300 IDENTIFY DEVICE
ef 00 03 00 42 00 00 00 00 00 00 a0 08 00:05:00.300 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 08 30 a0 08 00:05:00.300 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:05:00.300 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 00:05:00.300 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 1 (0x0001)
Device State: Active (0)
Current Temperature: 0 Celsius
Power Cycle Min/Max Temperature: --/ 0 Celsius
Lifetime Min/Max Temperature: --/ 0 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -127/127 Celsius
Min/Max Temperature Limit: -127/127 Celsius
Temperature History Size (Index): 478 (385)
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 2) ==
0x01 0x008 4 112 --- Lifetime Power-On Resets
0x01 0x018 6 7740088834 --- Logical Sectors Written
0x01 0x020 6 354755323 --- Number of Write Commands
0x01 0x028 6 9876506824 --- Logical Sectors Read
0x01 0x030 6 238596505 --- Number of Read Commands
0x01 0x038 6 96303600000 --- Date and Time TimeStamp
0x07 ===== = = === == Solid State Device Statistics (rev 1) ==
0x07 0x008 1 17 N-- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 253 Command failed due to ICRC error
0x0003 2 68 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 4 146 Device-to-host register FISes sent due to a COMRESET
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
View Git Blame Copy Permalink