conf.d: remove network file fragnents
This commit is contained in:
parent
a3133fec25
commit
2108285d64
@ -1,4 +0,0 @@
|
||||
|
||||
# You can assign a default route
|
||||
#defaultroute="192.168.0.1"
|
||||
#defaultroute6="2001:a:b:c"
|
@ -1,4 +0,0 @@
|
||||
|
||||
# You can assign a default route
|
||||
#defaultroute="192.168.0.1"
|
||||
#defaultroute6="2001:a:b:c"
|
@ -1,4 +0,0 @@
|
||||
|
||||
# You can assign a default route
|
||||
#defaultroute="gw 192.168.0.1"
|
||||
#defaultroute6="gw 2001:a:b:c"
|
@ -1,43 +0,0 @@
|
||||
|
||||
# You can assign a default route
|
||||
#defaultroute="gw 192.168.0.1"
|
||||
#defaultroute6="gw 2001:a:b:c"
|
||||
|
||||
# ifconfig under Linux is not that powerful and doesn't easily handle
|
||||
# multiple addresses
|
||||
# On the other hand, ip (iproute2) is quite powerful and is also supported
|
||||
#ip_eth0="192.168.0.10/24; 192.168.10.10/24"
|
||||
|
||||
# You can also use ip to add the default route.
|
||||
#defaultiproute="via 192.168.0.1"
|
||||
#defaultiproute6="via 2001:a:b:c"
|
||||
|
||||
# ip doesn't handle MTU like ifconfig, but we can do it like so
|
||||
#ifup_eth0="ip link set \$int mtu 1500"
|
||||
|
||||
# Create a bonded interface
|
||||
#interfaces="bond0"
|
||||
#ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0"
|
||||
#ifconfig_bond0="192.168.0.10 netmask 255.255.255.0"
|
||||
#ifdown_bond0="rmmod bonding"
|
||||
|
||||
# Create tap interface and a bridge interface.
|
||||
# We add the tap to the bridge.
|
||||
# An external program, like dhcpcd, will configure the IP on the bridge
|
||||
#interfaces="tun0 br0"
|
||||
#ifup_tun0="tunctl -t \$int"
|
||||
#ifdown_tun0="tunctl -d \$int"
|
||||
#ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2"
|
||||
#ifdown_br0="ifconfig \$int down; btctl delbr \$int"
|
||||
|
||||
# Create VLAN
|
||||
#interfaces="eth0_2 eth0_3 eth0_4"
|
||||
#ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4"
|
||||
#ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0"
|
||||
#ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0"
|
||||
#ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0"
|
||||
#ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4"
|
||||
|
||||
# Normally you would use wpa_supplicant to configure wireless, but you can
|
||||
# use iwconfig also
|
||||
#ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar"
|
@ -1,28 +0,0 @@
|
||||
# Assign static IP addresses and run custom scripts per interface.
|
||||
# Seperate commands with ;
|
||||
# Prefix with ! to run a shell script.
|
||||
# Use \$int to represent the interface
|
||||
#ifconfig_eth0="192.168.0.10 netmask 255.255.255.0"
|
||||
|
||||
# You also have ifup_eth0 and ifdown_eth0 to run other commands when
|
||||
# eth0 is started and stopped.
|
||||
# You should note that we don't stop the network at system shutdown by default.
|
||||
# If you really need this, then set keep_network=NO
|
||||
|
||||
# Lastly, the interfaces variable pulls in virtual interfaces that cannot
|
||||
# be automatically detected.
|
||||
#interfaces="br0 bond0 vlan0"
|
||||
|
||||
# You can also use files instead of variables here if you like:
|
||||
# /etc/ifconfig.eth0 is equivalent to ifconfig_eth0
|
||||
# /etc/ip.eth0 is equivalent to ifconfig_eth0
|
||||
# /etc/ifup.eth0 is equivalent to ifup_eth0
|
||||
# /etc/ifdown.eth0 is equivalent to ifdown_eth0
|
||||
# Any files found will automatically be put into the interfaces variable.
|
||||
# You don't need to escape variables in files, so use $int instead of \$int.
|
||||
|
||||
# If you require DHCP, you should install dhcpcd and it to the boot or
|
||||
# default runlevel.
|
||||
|
||||
# NIS users can set the domain name here
|
||||
#domainname="foobar"
|
Loading…
Reference in New Issue
Block a user