80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/HDD/Samsung/HD161/HD161HJ/3255D00FA5E4
Andrey Ponomarenko 06d1e49c98 Update of reports (new: 3633, modified: 0)
2023-02-14 01:25:13 +03:00

261 lines
12 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.0-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD161HJ
Serial Number: --
LU WWN Device Id: 5 0000f0 ...
Firmware Version: JF100-19
User Capacity: 160,041,885,696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database 7.3/5319
ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is: Fri May 27 13:12:27 2022 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 2891) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 49) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0
3 Spin_Up_Time POS--- 253 253 025 - 4416
4 Start_Stop_Count -O--CK 087 087 000 - 13551
5 Reallocated_Sector_Ct PO--CK 068 068 010 - 301
7 Seek_Error_Rate POSR-- 253 253 051 - 0
8 Seek_Time_Performance P-S--K 253 253 015 - 0
9 Power_On_Hours -O--CK 100 100 000 - 16596
10 Spin_Retry_Count PO--CK 253 253 051 - 0
11 Calibration_Retry_Count -O--C- 253 100 000 - 0
12 Power_Cycle_Count -O--CK 093 093 000 - 7738
13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 1074932
184 End-to-End_Error PO--CK 253 253 099 - 0
187 Reported_Uncorrect -O--CK 253 253 000 - 4915200
188 Command_Timeout -O--CK 253 253 000 - 0
190 Airflow_Temperature_Cel -O---K 157 112 000 - 27 (Min/Max 0/42)
194 Temperature_Celsius -O---K 154 109 000 - 28 (Min/Max 0/43)
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1074932
196 Reallocated_Event_Count -O--CK 068 068 000 - 301
197 Current_Pending_Sector -O--C- 253 100 000 - 0
198 Offline_Uncorrectable ----CK 253 253 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0
201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0
202 Data_Address_Mark_Errs -O--CK 253 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 14 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14 [5] occurred at disk power-on lifetime: 8037 hours (334 days + 21 hours)
When the command that caused the error occurred, the device was in a reserved state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
08 -- 00 3f 00 40 5c 1c 00 00 00 25 ff
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 00 00 00 00 00 00 00 00 00 00 00 00 49d+12:23:10.080 NOP [Abort queued commands]
00 20 16 00 92 00 02 00 0e 01 0b 00 a1 00:00:14.639 NOP [Reserved subcommand] [OBS-ACS-2]
Error 13 [4] occurred at disk power-on lifetime: 8037 hours (334 days + 21 hours)
When the command that caused the error occurred, the device was in a reserved state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
08 -- 00 37 00 40 5c 1c 00 00 00 25 ff
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 00 00 00 00 00 00 00 00 00 00 00 00 49d+12:23:10.080 NOP [Abort queued commands]
00 11 89 11 91 00 00 11 06 c9 b1 04 11 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
Error 12 [3] occurred at disk power-on lifetime: 25408 hours (1058 days + 16 hours)
When the command that caused the error occurred, the device was in a reserved state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
Error 11 [2] log entry is empty
Error 10 [1] log entry is empty
Error 9 [0] log entry is empty
Error 8 [7] occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 00 00 01 e0 cd de 00 00 0c 35 00 at LBA = 0xe0cddf00000c = 247174814236684
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
41 01 00 0c 00 35 00 00 e0 cd dd 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5]
41 01 00 0c 00 35 00 00 e0 cd dc 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5]
41 01 00 0c 00 35 00 00 e0 cd db 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5]
41 01 00 0c 00 35 00 00 e0 cd da 00 00 00:00:00.030 READ VERIFY SECTOR(S) (w/o retry) [OBS-5]
00 20 16 00 cd 00 02 00 0e 00 0b 00 98 00:00:14.782 NOP [Reserved subcommand] [OBS-ACS-2]
Error 7 [6] occurred at disk power-on lifetime: 7296 hours (304 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 7f 00 40 df 6e 00 00 02 25 ff
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
01 00 80 02 87 25 00 00 40 df 6a 00 ff 49d+12:23:10.086 [RESERVED]
c3 00 06 00 bf 35 00 00 40 4d 25 00 ff 49d+12:23:10.086 [VENDOR SPECIFIC]
c3 00 08 03 17 35 00 00 40 15 69 00 ff 49d+12:23:10.086 [VENDOR SPECIFIC]
c3 00 70 02 6f 25 00 00 40 df cd 00 ff 49d+12:23:10.086 [VENDOR SPECIFIC]
00 20 16 00 92 00 02 00 0e 01 0b 00 a1 49d+12:23:24.719 NOP [Reserved subcommand] [OBS-ACS-2]
SMART Extended Self-test Log (GP Log 0x07) not supported
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 28 Celsius
Power Cycle Min/Max Temperature: 14/28 Celsius
Lifetime Min/Max Temperature: 0/45 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -4/72 Celsius
Min/Max Temperature Limit: -9/77 Celsius
Temperature History Size (Index): 128 (33)
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 0 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
0x8001 2 0 Vendor specific
View Git Blame Copy Permalink