mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
203 lines
9.8 KiB
Plaintext
203 lines
9.8 KiB
Plaintext
smartctl 7.3 2022-02-28 r5338 [OpenBSD 7.2 amd64] (local build)
|
|
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Model Family: Toshiba 2.5" HDD MK..75GSX
|
|
Device Model: TOSHIBA MK6475GSX
|
|
Serial Number: --
|
|
LU WWN Device Id: 5 000039 ...
|
|
Firmware Version: GT001M
|
|
User Capacity: 640,135,028,736 bytes [640 GB]
|
|
Sector Size: 512 bytes logical/physical
|
|
Rotation Rate: 5400 rpm
|
|
Form Factor: 2.5 inches
|
|
Device is: In smartctl database 7.3/5319
|
|
ATA Version is: ATA8-ACS (minor revision not indicated)
|
|
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
|
|
Local Time is: Fri Dec 23 22:21:13 2022 EET
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART Status not supported: Incomplete response, ATA output registers missing
|
|
SMART overall-health self-assessment test result: PASSED
|
|
Warning: This result is based on an Attribute check.
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x00) Offline data collection activity
|
|
was never started.
|
|
Auto Offline Data Collection: Disabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: ( 120) seconds.
|
|
Offline data collection
|
|
capabilities: (0x5b) SMART execute Offline immediate.
|
|
Auto Offline data collection on/off support.
|
|
Suspend Offline collection upon new
|
|
command.
|
|
Offline surface scan supported.
|
|
Self-test supported.
|
|
No Conveyance Self-test supported.
|
|
Selective Self-test supported.
|
|
SMART capabilities: (0x0003) Saves SMART data before entering
|
|
power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x01) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 207) minutes.
|
|
SCT capabilities: (0x003d) SCT Status supported.
|
|
SCT Error Recovery Control supported.
|
|
SCT Feature Control supported.
|
|
SCT Data Table supported.
|
|
|
|
SMART Attributes Data Structure revision number: 16
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
|
|
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
|
|
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1337
|
|
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 8126
|
|
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 8
|
|
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
|
|
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
|
|
9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 11864
|
|
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0
|
|
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 7882
|
|
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 3900
|
|
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 745
|
|
193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 44267
|
|
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 41 (Min/Max 9/65)
|
|
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1
|
|
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
|
|
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
|
|
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
|
|
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 86
|
|
222 Loaded_Hours 0x0032 074 074 000 Old_age Always - 10749
|
|
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
|
|
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
|
|
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 237
|
|
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
|
|
|
|
SMART Error Log Version: 1
|
|
ATA Error Count: 114 (device log contains only the most recent five errors)
|
|
CR = Command Register [HEX]
|
|
FR = Features Register [HEX]
|
|
SC = Sector Count Register [HEX]
|
|
SN = Sector Number Register [HEX]
|
|
CL = Cylinder Low Register [HEX]
|
|
CH = Cylinder High Register [HEX]
|
|
DH = Device/Head Register [HEX]
|
|
DC = Device Command Register [HEX]
|
|
ER = Error register [HEX]
|
|
ST = Status register [HEX]
|
|
Powered_Up_Time is measured from power on, and printed as
|
|
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
|
|
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
|
|
|
|
Error 114 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
40 41 7a d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
60 80 88 d8 3b 01 40 00 02:06:37.514 READ FPDMA QUEUED
|
|
60 30 80 58 b1 f9 40 00 02:06:37.514 READ FPDMA QUEUED
|
|
60 40 78 c8 b1 c4 40 00 02:06:37.514 READ FPDMA QUEUED
|
|
60 40 70 ca e6 31 40 00 02:06:37.514 READ FPDMA QUEUED
|
|
60 28 60 f0 c2 88 40 00 02:06:37.514 READ FPDMA QUEUED
|
|
|
|
Error 113 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
40 41 22 d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
60 68 18 50 77 31 40 00 02:06:26.061 READ FPDMA QUEUED
|
|
60 08 08 30 60 03 40 00 02:06:26.056 READ FPDMA QUEUED
|
|
60 40 10 f2 2a d4 40 00 02:06:26.049 READ FPDMA QUEUED
|
|
60 20 18 8b a4 ff 40 00 02:06:26.045 READ FPDMA QUEUED
|
|
60 08 30 20 66 bc 40 00 02:06:26.045 READ FPDMA QUEUED
|
|
|
|
Error 112 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
40 41 6a d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
60 18 70 28 54 e1 40 00 02:05:26.484 READ FPDMA QUEUED
|
|
60 20 18 da b0 ff 40 00 02:05:26.480 READ FPDMA QUEUED
|
|
60 08 68 d0 b1 c4 40 00 02:05:26.474 READ FPDMA QUEUED
|
|
60 08 60 20 66 bc 40 00 02:05:26.473 READ FPDMA QUEUED
|
|
60 40 50 f2 2a d4 40 00 02:05:26.473 READ FPDMA QUEUED
|
|
|
|
Error 111 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
40 41 0a d0 b1 c4 66 Error: UNC at LBA = 0x06c4b1d0 = 113553872
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
60 08 58 20 f4 11 40 00 02:04:25.891 READ FPDMA QUEUED
|
|
60 20 50 da 44 67 40 00 02:04:25.891 READ FPDMA QUEUED
|
|
60 10 48 f8 e8 01 40 00 02:04:25.891 READ FPDMA QUEUED
|
|
61 08 68 00 10 fb 40 00 02:04:25.891 WRITE FPDMA QUEUED
|
|
60 08 40 40 59 f5 40 00 02:04:25.891 READ FPDMA QUEUED
|
|
|
|
Error 110 occurred at disk power-on lifetime: 7890 hours (328 days + 18 hours)
|
|
When the command that caused the error occurred, the device was active or idle.
|
|
|
|
After command completion occurred, registers were:
|
|
ER ST SC SN CL CH DH
|
|
-- -- -- -- -- -- --
|
|
40 41 6a d0 b1 c4 66 Error: WP at LBA = 0x06c4b1d0 = 113553872
|
|
|
|
Commands leading to the command that caused the error were:
|
|
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
|
|
-- -- -- -- -- -- -- -- ---------------- --------------------
|
|
61 08 70 e0 ef db 40 00 02:03:24.996 WRITE FPDMA QUEUED
|
|
60 08 68 d0 b1 c4 40 00 02:03:24.996 READ FPDMA QUEUED
|
|
61 08 68 60 13 d9 40 00 02:03:24.996 WRITE FPDMA QUEUED
|
|
60 08 60 20 66 bc 40 00 02:03:24.996 READ FPDMA QUEUED
|
|
61 08 60 e8 81 67 40 00 02:03:24.995 WRITE FPDMA QUEUED
|
|
|
|
SMART Self-test log structure revision number 1
|
|
No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
|
SMART Selective self-test log data structure revision number 1
|
|
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|
1 0 0 Not_testing
|
|
2 0 0 Not_testing
|
|
3 0 0 Not_testing
|
|
4 0 0 Not_testing
|
|
5 0 0 Not_testing
|
|
Selective self-test flags (0x0):
|
|
After scanning selected spans, do NOT read-scan remainder of disk.
|
|
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|
|
|
|
|