mirror of
https://github.com/bsdhw/SMART.git
synced 2025-05-31 16:21:41 +05:30
99 lines
4.9 KiB
Plaintext
99 lines
4.9 KiB
Plaintext
smartctl 7.2 2020-12-30 r5155 [NetBSD 9.99.85 amd64] (local build)
|
|
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
|
|
|
|
=== START OF INFORMATION SECTION ===
|
|
Model Family: Western Digital Blue
|
|
Device Model: WDC WD10EZEX-60WN4A0
|
|
Serial Number: --
|
|
LU WWN Device Id: 5 0014ee ...
|
|
Firmware Version: 01.01A01
|
|
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
|
|
Sector Sizes: 512 bytes logical, 4096 bytes physical
|
|
Rotation Rate: 7200 rpm
|
|
Form Factor: 3.5 inches
|
|
Device is: In smartctl database [for details use: -P show]
|
|
ATA Version is: ACS-3 T13/2161-D revision 5
|
|
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
|
|
Local Time is: Tue Jun 22 23:15:48 2021 CEST
|
|
SMART support is: Available - device has SMART capability.
|
|
SMART support is: Enabled
|
|
|
|
=== START OF READ SMART DATA SECTION ===
|
|
SMART overall-health self-assessment test result: PASSED
|
|
|
|
General SMART Values:
|
|
Offline data collection status: (0x82) Offline data collection activity
|
|
was completed without error.
|
|
Auto Offline Data Collection: Enabled.
|
|
Self-test execution status: ( 0) The previous self-test routine completed
|
|
without error or no self-test has ever
|
|
been run.
|
|
Total time to complete Offline
|
|
data collection: (11760) seconds.
|
|
Offline data collection
|
|
capabilities: (0x5b) SMART execute Offline immediate.
|
|
Auto Offline data collection on/off support.
|
|
Suspend Offline collection upon new
|
|
command.
|
|
Offline surface scan supported.
|
|
Self-test supported.
|
|
No Conveyance Self-test supported.
|
|
Selective Self-test supported.
|
|
SMART capabilities: (0x0003) Saves SMART data before entering
|
|
power-saving mode.
|
|
Supports SMART auto save timer.
|
|
Error logging capability: (0x01) Error logging supported.
|
|
General Purpose Logging supported.
|
|
Short self-test routine
|
|
recommended polling time: ( 2) minutes.
|
|
Extended self-test routine
|
|
recommended polling time: ( 122) minutes.
|
|
SCT capabilities: (0x303d) SCT Status supported.
|
|
SCT Error Recovery Control supported.
|
|
SCT Feature Control supported.
|
|
SCT Data Table supported.
|
|
|
|
SMART Attributes Data Structure revision number: 16
|
|
Vendor Specific SMART Attributes with Thresholds:
|
|
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
|
|
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
|
|
3 Spin_Up_Time 0x0027 173 169 021 Pre-fail Always - 2308
|
|
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 472
|
|
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
|
|
7 Seek_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
|
|
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1434
|
|
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
|
|
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
|
|
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 435
|
|
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
|
|
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
|
|
187 Reported_Uncorrect 0x0032 100 081 000 Old_age Always - 21
|
|
188 Command_Timeout 0x0032 100 082 000 Old_age Always - 85900656662
|
|
190 Airflow_Temperature_Cel 0x0022 071 065 040 Old_age Always - 29 (Min/Max 26/30)
|
|
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 126
|
|
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 508
|
|
194 Temperature_Celsius 0x0022 114 108 000 Old_age Always - 29
|
|
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
|
|
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
|
|
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
|
|
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
|
|
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
|
|
|
|
SMART Error Log Version: 1
|
|
No Errors Logged
|
|
|
|
SMART Self-test log structure revision number 1
|
|
No self-tests have been logged. [To run self-tests, use: smartctl -t]
|
|
|
|
SMART Selective self-test log data structure revision number 1
|
|
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
|
|
1 0 0 Not_testing
|
|
2 0 0 Not_testing
|
|
3 0 0 Not_testing
|
|
4 0 0 Not_testing
|
|
5 0 0 Not_testing
|
|
Selective self-test flags (0x0):
|
|
After scanning selected spans, do NOT read-scan remainder of disk.
|
|
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
|
|