80486DX2-66/SMART-open-study
1
0
Fork 0
mirror of https://github.com/bsdhw/SMART.git synced 2025-05-31 16:21:41 +05:30
Code Issues Activity
Files
master
SMART-open-study/HDD/WDC/WD5000/WD5000AVVS-00ZWB0/E2681D7191BE
Andrey Ponomarenko 6760e6c317 Update of reports (new: 1329, modified: 0)
2023-05-01 22:53:35 +03:00

312 lines
15 KiB
Plaintext
Raw Permalink Blame History

smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital AV-GP
Device Model: WDC WD5000AVVS-00ZWB0
Serial Number: --
LU WWN Device Id: 5 0014ee ...
Firmware Version: 01.01B01
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database 7.3/5319
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Thu Mar 16 12:51:42 2023 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 158) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 200 194 051 - 4
3 Spin_Up_Time PO---- 161 158 021 - 4941
4 Start_Stop_Count -O--CK 084 084 000 - 16055
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-- 200 200 051 - 0
9 Power_On_Hours -O--CK 070 070 000 - 22151
10 Spin_Retry_Count -O--C- 100 100 051 - 0
11 Calibration_Retry_Count -O--C- 100 100 051 - 0
12 Power_Cycle_Count -O--CK 085 085 000 - 15892
190 Airflow_Temperature_Cel -O---K 060 039 040 Past 40
192 Power-Off_Retract_Count -O--CK 193 193 000 - 5533
193 Load_Cycle_Count -O--CK 195 195 000 - 16055
194 Temperature_Celsius -O---K 107 086 000 - 40
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--C- 200 198 000 - 0
198 Offline_Uncorrectable ----C- 200 199 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 12
200 Multi_Zone_Error_Rate ---R-- 200 167 051 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x20 GPL R/O 1 Streaming performance log [OBS-8]
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 24 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 127 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 127 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 12 00 51 00 00 e0 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 d0 25 10 0f 00 00 00 00 00 00 00 18 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
00 01 00 00 64 10 83 18 0f 25 00 00 00 00:00:25.874 NOP [Abort queued commands]
18 d7 25 10 03 00 12 00 52 00 00 00 18 00:17:29.742 RECALIBRATE [RET-4]
00 07 00 00 78 10 d7 19 03 25 00 00 00 00:00:16.402 NOP [Abort queued commands]
Error 126 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 06 60 02 5a 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 01 00 00 10 02 04 00 5a 2f 00 00 08 00:00:47.312 DEVICE RESET
19 cb 61 02 49 00 d0 08 b8 08 00 00 1e 00:02:29.963 RECALIBRATE [RET-4]
08 c8 10 00 10 02 cb 1e 49 61 00 00 08 00:00:04.304 DEVICE RESET
Error 125 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 cb 60 02 49 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 d0 10 00 10 02 cb 1e 49 61 00 00 08 00:00:47.312 DEVICE RESET
1e ca 61 02 49 00 c8 08 10 10 00 00 18 00:02:29.963 RECALIBRATE [RET-4]
08 b8 10 00 10 02 ca 1e 49 60 00 00 08 00:00:04.288 DEVICE RESET
Error 124 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 d5 60 02 0c 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 01 00 00 10 02 d3 00 0c 2f 00 00 08 00:00:47.280 DEVICE RESET
19 28 2f 01 fc 00 b0 08 b8 08 00 00 00 00:02:10.090 RECALIBRATE [RET-4]
08 b0 08 00 b8 01 16 19 d1 60 00 00 08 00:00:04.097 DEVICE RESET
Error 123 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 2a 60 01 fc 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 01 00 00 10 01 28 00 fc 2f 00 00 08 00:00:47.280 DEVICE RESET
19 14 2f 01 d1 00 b0 08 b8 08 00 00 00 00:01:59.062 RECALIBRATE [RET-4]
08 b0 08 00 b8 01 e7 19 be 60 00 00 08 00:00:04.097 DEVICE RESET
Error 122 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 16 60 01 d1 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 01 00 00 10 01 14 00 d1 2f 00 00 08 00:00:47.280 DEVICE RESET
19 e5 2f 01 be 00 b0 08 b8 08 00 00 00 00:01:54.407 RECALIBRATE [RET-4]
08 b0 08 00 b8 01 55 19 ae 60 00 00 08 00:00:04.097 DEVICE RESET
Error 121 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 e7 60 01 be 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 01 00 00 10 01 e5 00 be 2f 00 00 08 00:00:47.280 DEVICE RESET
19 54 60 01 ae 00 b0 08 b8 08 00 00 19 00:01:50.165 RECALIBRATE [RET-4]
08 b0 08 00 c8 01 54 19 ae 60 00 00 08 00:00:51.376 DEVICE RESET
Error 120 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 00 01 00 00 51 00 00 40 01 00 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
00 55 60 01 ae 00 00 00 00 00 00 00 19 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2]
08 b0 08 00 c8 01 54 19 ae 60 00 00 08 00:00:47.280 DEVICE RESET
19 53 60 01 ae 00 b0 08 c8 08 00 00 19 00:01:50.164 RECALIBRATE [RET-4]
08 b0 00 00 68 01 46 19 ae 60 00 00 08 00:00:26.800 DEVICE RESET
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 16523 -
# 2 Extended offline Aborted by host 90% 1541 -
# 3 Short offline Completed without error 00% 1522 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 40 Celsius
Power Cycle Min/Max Temperature: 23/40 Celsius
Lifetime Min/Max Temperature: 23/61 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/85 Celsius
Temperature History Size (Index): 128 (30)
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x8000 4 4329 Vendor specific
View Git Blame Copy Permalink